Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
The
is a PoE injector designed for industrial
environments, especially for rolling stock, vehicle, and railway applications
due to its EN50155 compliance and M12 connectors. With one
10/100/1000 Base-T(X) port compliant with IEEE802.3at/af standards, the
is equipped with intelligent detection function. As a
result, the devices will not turn on power until it detects a valid PoE
signature from the connected PoE devices. This function can protect non-
PoE compliant equipment connected to the same Ethernet cable from
damage and allow only IEEE 802.3at/802.3af compliant devices to be
powered by the PoE injector. The PoE injector can function with any P.D.
equipment which is fully compliant with IEEE 802.3at/802.3af PoE standards.
TINJ-101GT-M12
TINJ-101GT-M12
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Hold the
evice upright against the wall
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Slide the
evice downwards and tighten the four screws for added stability.
Step 1:
Step 2:
Step 3:
d
d
The product is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
Contents
TINJ-101GT-M12 or
TINJ-101GT-M12-24V
Pictures
Number
1
QIG
1
Dimension
Panel Layouts
Front View
1.
2.
3. Power input port
4. PoE status LED
5. Power status LED
Data input port
PoE port
Network Connection
The device provides one data input port and one PoE data output port in M12 connector. According
to the link type, the device uses CAT 3, 4, 5, 5e UTP cables to connect to any other network
devices (Pcs, servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
TINJ-101GT-M12
1907-2-29-TINJ101GTM12-1.0
PoE
INJECTOR
PoE
INJECTOR
EN50155
I N D U S T R I A L
1
3
4
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the switch
between the wall and the screws.
For pin assignments of the LAN ports, please refer to the following tables.
178.2
R2.5
R4.00
40.0
15.0
7.50
150.0
44.4
73.9
138.0
88.9
EN50155 Industrial PoE Injector
TINJ-101GT-M12
PoE OUT
PoE
V-
V+
N.C.
N.C.
N.C.
PWR
PWR
4
5
6
7
8
2
1
1 DC+
2 DD+
3 DD-
4 DA-
5 DB+
6 DA+
7 DC-
8 DB-
3
1 DC+
2 DD+
3 DD-
4 DA- / PoE Vout+
5 DB+ / PoE Vout-
6 DA+ / PoE Vout+
7 DC-
8 DB- / PoE Vout-
Data IN
TINJ-101GT-M12
PoE OUT
PoE
V-
V+
N.C.
N.C.
N.C.
PWR
PWR
4
5
6
7
8
2
1
1 DC+
2 DD+
3 DD-
4 DA-
5 DB+
6 DA+
7 DC-
8 DB-
3
1 DC+
2 DD+
3 DD-
4 DA- / PoE Vout+
5 DB+ / PoE Vout-
6 DA+ / PoE Vout+
7 DC-
8 DB- / PoE Vout-
Data IN
TINJ-101GT-M12
2
5
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-TX
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
M12
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
M12
1000BASE-T
Cat. 5/Cat. 5e 100-ohm UTP
UTP 100 m (328ft)
M12
4
5
6
7
8
2
1
3
1 DC+
2 DD+
3 DD-
4 DA- / PoE Vout+
5 DB+ / PoE Vout-
6 DA+ / PoE Vout+
7 DC-
8 DB- / PoE Vout-
10/100 Base-T(X)
M12 Input (Data Only)
M12 Output (Data and Power)
Pin
Symbol
Description
Symbol
Description
1
NC
Not Connected
NC
Not Connected
2
NC
Not Connected
NC
Not Connected
3
NC
Not Connected
NC
Not Connected
4
Rx-
Data Receive
Rx- (Vdc+)
Data Receive and
Feeding power(+)
5
Tx+
Data Transmit
Tx+ (Vdc-)
Data Transmit and
Feeding power(-)
6
Rx+
Data Receive
Rx+ (Vdc+)
Data Receive and
Feeding power(+)
7
NC
Not Connected
NC
Not Connected
8
Tx-
Data Transmit
Tx- (Vdc-)
Data Transmit and
Feeding power(-)
1000 Base-T
M12 Input (Data Only)
M12 Output (Data and Power)
Pin
Symbol
Description
Symbol
Description
1
BI_DC+
Data BI_DC+
BI_DC+
Data BI_DC+
2
BI_DD+
Data BI_DD+
BI_DD+
Data BI_DD+
3
BI_DD-
Data BI_DD-
BI_DD-
Data BI_DD-
4
BI_DA-
Data BI_DA-
BI_DA-
(Vdc+)
Data BI_DA- and
Feeding Power(+)
5
BI_DB+
Data BI_DB+
BI_DB+
(Vdc-)
Data BI_DB+ and Feeding
Power(-)
6
BI_DA+
Data BI_DA+
BI_DA+
(Vdc+)
Data BI_DA+ and Feeding
Power(+)
7
BI_DC-
Data BI_DC-
BI_DC-
Data BI_DC-
8
BI_DB-
Data BI_DB-
BI_DB-
(Vdc-)
Data BI_DB- and
Feeding Power(-)
Power inputs
The device provides one set of power supply using the M12 5-pin female
connector on the front panel. Please refer to the following figure for pin
assignments.
V-
V+
N.C.
N.C.
N.C.
