Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
The
is a managed Redundant Ring Ethernet switch with
TGPS-9168GT-M12
16x10/100/1000Base-T(X) P.S.E. ports and 8x10/100/1000Base-T(X) ports.
The switch supports various Ethernet redundancy protocols such as O-Ring
(recovery time < 30ms over 250 units of connection), O-Chain and MSTP
(RSTP/STP compatible) to protect your mission-critical applications from
network interruptions or temporary malfunctions. With EN50155 compliance
and M12 connectors, the device is a perfect choice for the toughest industrial
environments as the features can ensure tight, robust connections, and
guarantee reliable operation against environmental disturbances, such as
vibration and shock. The device also supports Power-over-Ethernet which
enables electrical power (up to 15.4 watts) to be transmitted along with data
over standard twisted-pair Ethernet cables. Supporting wide operating
temperature from -40 to 75 degrees, the device can be managed centrally via
O p e n - Vi s i o n , t h e We b - b a s e d i n t e r f a c e , Te l n e t a n d c o n s o l e ( C L I )
configuration.
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Step 1:
Hold the
evice upright against the wall
d
Step 2:
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screws to the wall with a screwdriver.
Step 3:
Slide the
evice downwards and tighten the four screws for added stability.
d
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative
for assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow:
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Mechanical Loading:
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TGPS-9168GT-M12
Pictures
Number
1
CD
1
Dimension
Panel Layouts
Front View
1. Reset button
2. Power LED
3. R.M. status LED
4. Ring status LED
5. Fault LED
6. Console port
7. Relay output port
8. Power connector
9. Gigabit Ethernet ports
10. PoE-enabled Gigabit Ethernet ports
11. Link/ACT LED for Gigabit ports
12. Speed LED for Gigabit ports
13. Link/ACT LED for PoE-enabled Gigabit
Ethernet ports
14. Speed LED for PoE-enabled Gigabit
Ethernet ports
15. PoE LED
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for dual power inputs.
Step 1:
Insert a power cable to the power connector on the device.
Step 2:
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay
N.C.
3A@24VDC
Network Connection
The device provides Ethernet ports in M12 connector type. According to the link type, the switch
uses CAT
e UTP cables to connect to any other network devices PCs servers switches
3, 4, 5,5
(
,
,
,
routers or hubs
Please refer to the following table for cable specifications.
,
).
TGPS-9168GT-M12
TGPS-9168GT-M12
1907-2-29-TGPS9168GTM12-1.0
S w i tc h
E N 5 0 1 5 5
I N D U S T R I A L
6
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
M12 A-coding connector
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
M12 A-coding connector
1000BASE-T
Cat. 5/Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
M12 A-coding connector
For pin assignments of the Ethernet ports, please refer to the following tables.
QIG
1
15
7
14
12
13
4
5
6
7
8
2
1
3
4 5
1
2 3
The switch uses the M12 A-coded 5-pin female connector
on the front panel for relay output. Use a cable with an M12
A-coded 5-pin male connector to connect the relay. The
relay contacts will detect user-configured events and form
an close circuit when an event is triggered.
Console port pinouts
RS-232, 9600bps, 8, N, 1
EN50155 24-port managed
Gigabit PoE Ethernet switch
8
9
10
11
RSVD
RXD
GND
TXD
N.C.
The switch has one RS-232 (M12 5pin) console port,
located on the front panel. Use a M12-to-DB9
console cable to connect the console port to your
PC's COM port.
3A@24VDC
Relay
N.C.
Relay Output
Console
RSVD
RXD
RS-232, 115200bps, 8, N, 1
GND
TXD
N.C.
Power
G1
LNK/ACT
Speed
G2
LNK/ACT
Speed
G3
LNK/ACT
Speed
G4
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
G5
G6
G7
G8
V1+
V1-
V2+
V2-
PoE
PoE
PoE
PoE
4
5
6
7
8
2
1
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
3
G1~G8
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
PoE
PoE
PoE
PoE
Fault
Ring
R.M.
PWR2
PWR1
Reset
G9
G10
G11
G12
G13
G14
G15
G16
G17
G18
G19
G20
G21
G22
G23
G24
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA- / PoE Vout+
5 BI_DB+ / PoE Vout-
6 BI_DA+ / PoE Vout+
7 BI_DC-
8 BI_DB- / PoE Vout-
G9~G24
TGPS-9168GT-M12
3A@24VDC
Relay
N.C.
Relay Output
Console
RSVD
RXD
RS-232, 115200bps, 8, N, 1
GND
TXD
N.C.
Power
G1
LNK/ACT
Speed
G2
LNK/ACT
Speed
G3
LNK/ACT
Speed
G4
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
G5
G6
G7
G8
V1+
V1-
V2+
V2-
PoE
PoE
PoE
PoE
4
5
6
7
8
2
1
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
3
G1~G8
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
LNK/ACT
Speed
PoE
PoE
PoE
PoE
Fault
Ring
R.M.
PWR2
PWR1
Reset
G9
G10
G11
G12
G13
G14
G15
G16
G17
G18
G19
G20
G21
G22
G23
G24
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA- / PoE Vout+
5 BI_DB+ / PoE Vout-
6 BI_DA+ / PoE Vout+
7 BI_DC-
8 BI_DB- / PoE Vout-
G9~G24
TGPS-9168GT-M12
8-Pin Gigabit Non-PoE Port
Definition
PIN
Definition
1
BI_DC+
2
BI_DD+
3
BI_DD-
4
BI_DA-
5
BI_DB+
6
BI_DA+
7
BI_DC-
8
BI_DB-
8-Pin Gigabit PoE Port
Definition
PIN
Definition
1
BI_DC+
2
BI_DD+
3
BI_DD-
4
BI_DA- with PoE Vout+
5
BI_DB+ with PoE Vout-
6
BI_DA+ with PoE Vout+
7
BI_DC-
8
BI_DB- with PoE Vout-
