Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
With 24VDC power supply, the
and
unmanaged Gigabit PoE Ethernet switches are designed for
industrial applications, such as rolling stock, vehicle, and railway
applications. The switches boast EN50155 compliance and M12 connectors
to ensure tight and robust connections, and guarantee reliable operation
against environmental disturbances, such as vibration and shock. Both
models feature eight 10/100/1000Base-T(X) P.S.E. ports which are able to
provide sufficient power for those power-hungry devices with up to 30Watts
per port. Therefore, you can attach an IEEE 802.3af-compliant device to the
switch without requiring additional power. The
model also provides two sets of bypass ports that ensure constant network
connectivity during power failure. Even if the switch loses power, traffic
will continue to flow unimpeded through the link.
TGPS-1080-M12-24V
TGPS-1080-M12-
BP2-24V
TGPS-1080-M12-BP2-24V
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Hold the
evice upright against the wall
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Slide the
evice downwards and tighten the four screws for added stability.
Step 1:
Step 2:
Step 3:
d
d
The
are shipped with the
following items. If any of these items is missing or damaged, please contact
your customer service representative for assistance.
TGPS-1080-M12-24V/ TGPS-1080-M12-BP2-24V
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TGPS-1080-M12-24V or
TGPS-1080-M12-BP2-24V
Pictures
Number
1
QIG
1
Dimension
TGPS-1080-M12-24V
TGPS-1080-M12-BP2-24V
Panel Layouts
Front View
1. Power status LED
2. Power1 status LED
3. Power2 status LED
4. Fault LED
5. Power port
6. Relay output port
7. LAN port LNK/ACT LED
8. LAN port Duplex/Collision LED
9. Gigabit Ethernet ports
(G5-G8 of TGPS-1080-M12-BP2-24V are bypass ports)
10. PoE status LED
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Insert a power cable to the power connector on the device.
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Step 1:
Step 2:
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay
N.C.
1A@24VDC
Network Connection
The switch has eight 10/100/1000Base-T(X) Ethernet ports in the form of M12 connector. These
ports are PoE-enabled, and thus can deliver power over the same Ethernet cable. Depending on
the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect to network devices (Pcs,
servers, switches, routers, or hubs). Please refer to the following table for cable
specifications.
M12/8P Pin Definition
TGPS-1080-M12 Series
TGPS-1080-M12 Series
1907-2-29-TGPS1080M12-1.0
Switch
EN50155
EN50155 8-port unmanaged
PoE Ethernet switch
I N D U S T R I A L
125.0
196.0
R2.5
R4.00
155.8
65.0
21.3
15.0
7.50
168.4
56.5
86.0
TGPS-1080-M12-BP2
G1
G5
G2
G6
G3
G7
G4
G8
Fault
PWR2
Power
PWR1
PWR
Relay
N.C.
3A@24VDC
Relay Output
V1+
V1-
V2+
V2-
LNK/ACT
DPX/COL
PoE
LNK/ACT
DPX/COL
PoE
LNK/ACT
DPX/COL
PoE
LNK/ACT
DPX/COL
PoE
Power
Failure
Bypass
125.0
196.0
R2.5
R4.00
155.8
65.0
21.3
15.0
7.50
168.4
56.5
86.0
TGPS-1080-M12
G1
G5
G2
G6
G3
G7
G4
G8
Fault
PWR2
Power
PWR1
PWR
Relay
N.C.
3A@24VDC
Relay Output
V1+
V1-
V2+
V2-
LNK/ACT
DPX/COL
PoE
LNK/ACT
DPX/COL
PoE
LNK/ACT
DPX/COL
PoE
LNK/ACT
DPX/COL
PoE
TGPS-1080-M12
G1
G5
G2
G6
G3
G7
G4
G8
Fault
PWR2
Power
PWR1
PWR
Relay
N.C.
3A@24VDC
Relay Output
V1+
V1-
V2+
V2-
LNK/ACT
DPX/COL
PoE
LNK/ACT
DPX/COL
PoE
LNK/ACT
DPX/COL
PoE
LNK/ACT
DPX/COL
PoE
1
2
3
4
5
6
7
8
9
9
10
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the switch
between the wall and the screws.
The switch uses the M12 A-coded 5-pin male connector on
the front panel for relay output. Use a power cord with an
M12 A-coded 5-pin female connector to connect the relay.
The relay contacts will detect user-configured events and
form an open circuit when an event is triggered.
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
8-pin female M12
A-coding connector
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
8-pin female M12
A-coding connector
1000BASE-T
Cat. 5/Cat. 5e 100-ohm
UTP
UTP 100 m (328ft)
8-pin female M12
A-coding connector
4
5
6
7
8
2
1
3
For pin assignments of the LAN ports, please refer to the following tables.
10/100Base-T(X) P.S.E. RJ-45 port
Pin No.
Description
#1
TD+ with PoE Power input +
#2
TD- with PoE Power input +
#3
RD+ with PoE Power input -
#6
RD- with PoE Power input -
1000Base-T P.S.E. RJ-45 port
Pin No.
Description
#1
BI_DA+ with PoE Power input +
#2
BI_DA- with PoE Power input +
#3
BI_DB+ with PoE Power input -
#4
BI_DC+
#5
BI_DC-
#6
BI_DB- with PoE Power input -
#7
BI_DD+
#8
BI_DD-
Bypass port pinouts
TGPS-1080-M12-BP2-24V includes 2 sets of bypass
ports that protect the network from failures by ensuring
network integrity during power loss.
4
5
6
7
8
2
1
3