Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
1907-2-29-TGAR+GPS-1.0
Designed for industrial and rolling stock wireless applications with two LAN
ports in M12 connectors and EN50155 compliance, the
are IEEE802.11 a/b/g/n routers capable of
providing a fast and effective way to communicate with the Internet over
wired or wireless LANs. The series includes PoE models and 3G/4G models
with GPS functions. The series of devices can be configured to operate in 3
modes of routing function: dynamic/static IP route, PPPoE authentication,
and cellular modem dial up. You can set up WLAN environment to fulfill
demands of various applications rapidly by dialing up cellular modem. With
dual Ethernet ports in switch mode, you can use Daisy Chain to reduce the
usage of Ethernet switch ports. The router also provides VPN capabilities
which create encrypted virtual tunnels on the Internet, allowing remote or
mobile users to connect to the network of your office.
TGAR-
1062/2062/1662+ series
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below
to install the device on the wall.
Hold the
evice upright against the wall
Insert four screws through the large opening of
the keyhole-shaped apertures at the top and bottom of
the unit and fasten the screw to the wall with a screwdriver.
Slide the
evice downwards and tighten the four
screws for added stability.
Step 1:
Step 2:
Step 3:
d
d
The devices are shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
CD
3G or 4G Antenna
Router
Pictures
Number
1
1
QIG
1
2.4GHz/5GHz Wi-Fi
Antenna
2 (TGAR-1062+/2062+) or
4 (TGAR-1662+)
Dimension
Panel Layouts
Front Panel
Power
DO
DI
ETH2
(P.O.E)
ETH1
Console
Relay Output
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
4
5
6
7
8
2
1
3
V1+
V1-
V2+
V2-
RSVD
RxD
RS-232, 115200bps, 8, N, 1
GND
TxD
N.C.
Relay
N.C.
1A@24VDC
DI1
COM
DI2
DI3
DI4
GND
DO1
DO2
DO3
DO4
TGAR-1062+-GPS-M12
PWR1
PWR2
(P.O.E)
ETH1
ETH2
Fault
WLAN
1
3
2
5
6
7
8
9
10
TGAR-1062+-3/4GS-M12
11
TGAR-1662+-3/4GS-M12
1. PWR status LED
(PW2 with PoE indicator)
2. LAN port status LED
3. Fault status LED
4. WAN status LED
Wireless
EN50155
ACCESS POINT ROUTER
EN50155 Industrial Wireless LAN
PoE Access Point Router
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Insert a power cable to the power connector on the device.
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Step 1:
Step 2:
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay
N.C.
1A@24VDC
DI/DO Port Pinouts
DO
DI
DI1
COM
DI2
DI3
DI4
GND
DO1
DO2
DO3
DO4
Network Connection
The AP router has two 10/100/1000 Base-T(X) Ethernet ports. According to the link type, the AP
router uses CAT 3, 4, 5, 5e, UTP cables to connect to any other network device (PCs, servers,
evicees, routers, or hubs). Please refer to the following table for cable specifications.
d
Cable
Type
Max. Length
Connector
10Base-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
M12
100Base-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
M12
1000Base-T
Cat. 5/Cat. 5e 100-ohm UTP UTP 100 m (328 ft)
M12
1 (TGAR-1062+/1662+) or
2 (TGAR-2062+)
SIMC
ardSlot
Cellular
ANT.
Power
DO
DI
ETH2
(P.O.E)
ETH1
Console
Relay Output
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
4
5
6
7
8
2
1
3
V1+
V1-
V2+
V2-
RSVD
RxD
RS-232, 115200bps, 8, N, 1
GND
TxD
N.C.
Relay
N.C.
1A@24VDC
DI1
COM
DI2
DI3
DI4
GND
DO1
DO2
DO3
DO4
TGAR+ GPS Series
PWR1
PWR2
(P.O.E)
ETH1
ETH2
Fault
WAN
WLAN1
WLAN2
R2.5
168.4
7.50
R4.0
86.0
56.5
3.50
WIFI1
ANT
.1
WIFI2
ANT
.1
Reset
196.1
125.6
15.0
65
19.1
12.5
WAN
TGAR-2062+-3/4GS-M12
5. WLAN status LED
6. Relay output port
7. Console port
8. Ethernet LAN ports
(ETH2 with PoE)
4
13
12
Power
DO
DI
ETH2
(P.O.E)
ETH1
Console
Relay Output
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
4
5
6
7
8
2
1
3
V1+
V1-
V2+
V2-
RSVD
RxD
RS-232, 115200bps, 8, N, 1
GND
TxD
N.C.
Relay
N.C.
1A@24VDC
DI1
COM
DI2
DI3
DI4
GND
DO1
DO2
DO3
DO4
TGAR-2062+-GPS-M12
PWR1
PWR2
(P.O.E)
ETH1
ETH2
Fault
WLAN
1
3
2
5
6
7
8
9
10
11
WAN1
4
13
12
WAN2
Power
DO
DI
ETH2
(P.O.E)
ETH1
Console
Relay Output
1 BI_DC+
2 BI_DD+
3 BI_DD-
4 BI_DA-
5 BI_DB+
6 BI_DA+
7 BI_DC-
8 BI_DB-
4
5
6
7
8
2
1
3
V1+
V1-
V2+
V2-
RSVD
RxD
RS-232, 115200bps, 8, N, 1
GND
TxD
N.C.
Relay
N.C.
1A@24VDC
DI1
COM
DI2
DI3
DI4
GND
DO1
DO2
DO3
DO4
TGAR-1662+-GPS-M12
PWR1
PWR2
(P.O.E)
ETH1
ETH2
Fault
WLAN1
1
3
2
5
6
7
8
9
10
11
WAN
4
13
12
WLAN2
WIFI
ANT
.1
Reset
1
2
1. 3G/4G Antenna connector
2. Reset button
3. GPS antenna connector
Side Panel
Allen Key
1
PoE
Circuit Overloading:
Consideration should be given to the connection of the equipment to
the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
9. DI/DO ports
10. Power connector
11. 2.4/5GHz Wi-Fi antenna
12. Cellular antenna connector
13. SIM card slot
14. Ground
WIFI
ANT
.1
GPS
ANT
1
3
Bottom Panel
TGAR-2062+-3/4GS-M12
SIM
Ca
rd
Slo
t2
Cellular2
ANT.
Top Panel
SIMC
ardS
lot
Cellular
ANT.
SIM
Ca
rd
Slo
t
Cellular
ANT.
TGAR-1062+/1662+
-3/4GS-M12
TGAR-2062+-3/4GS-M12
TGAR+ GPS Series
TGAR+ GPS Series
14
14
13
12
14
