Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
Q I G
The
is a managed Ethernet switch designed for
industrial applications, such as rolling stock, vehicle, and railway
applications. The switch boasts EN50155 compliance and M12 connectors
to ensure tight and robust connections, and guarantee reliable operation
against environmental disturbances, such as vibration and shock. Besides
eight 10/100Base-T(X) ports, the switch also provides one set of bypass
ports that ensure constant network connectivity if power outage or node
failure occurs. In such situations, the device will bypass the inactive
switch and continue to transfer network traffic to the next switch in the relay.
TES-3082GT-M12-BP1
Package Contents
Installation
Wall-mount
The device can be fixed to the wall. Follow the steps below to install the device on the wall.
Hold the
evice upright against the wall
Insert four screws through the large opening of the keyhole-shaped apertures at the
top and bottom of the unit and fasten the screw to the wall with a screwdriver.
Slide the
evice downwards and tighten the four screws for added stability.
Step 1:
Step 2:
Step 3:
d
d
The
series is shipped with the following items. If any
of these items is missing or damaged, please contact your customer service
representative for assistance.
TES-3082GT-M12-BP1
Preparation
Before you begin installing the device, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
Circuit Overloading:
If installed in a closed environment, make sure
the operating ambient temperature is compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Make sure the amount of air flow required for safe operation
of the equipment is not compromised during installation.
Make sure the mounting of the equipment is not in a
hazardous condition due to uneven mechanical loading.
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits
might have on overcurrent protection and supply wiring. Appropriate
consideration of equipment nameplate ratings should be used when addressing
this concern.
Safety & Warnings
For pin assignments of power, console and relay output ports, please refer to the following tables.
Contents
TES-3082GT-M12-BP1
Pictures
Number
1
CD
1
Dimension
Panel Layouts
Front View
1. Reset button
2. Power1 status LED
3. Power2 status LED
4. R.M. status LED
5. Ring status LED
6. Fault LED
7. Relay output port
8. Console port
9. Power connector
10. Ethernet ports
11. LNK/ACT indicator for Ethernet port
12. Duplex/collision indicator for Ethernet port
13. LNK/ACT indicator for Gigabit Ethernet port
14. Speed indicator for Gigabit Ethernet port
15. Gigabit Ethernet ports
Wiring
Grounding
Grounding and wire routing help limit the effects of noise due to electromagnetic interference
(EMI). Run the ground connection from the grounding pin on the power connector to the grounding
surface prior to connecting devices.
Power port pinouts
The device supports two sets of power supplies and uses the M23 5-pin
female connector on the front panel for the dual power inputs.
Insert a power cable to the power connector on the device.
Rotate the outer ring of the cable connector until a snug fit is
achieved. Make sure the connection is tight.
Step 1:
Step 2:
V1+
V1-
V2+
V2-
Relay output port pinouts
Relay
N.C.
1A@24VDC
Network Connection
The switch has eight 10/100Base-T(X) and two 10/100/1000Base-T(X) Ethernet ports in the form of
M12 connector. Depending on the link type, the switch uses CAT 3, 4, 5,5e UTP cables to connect
to network devices (PCs, servers, switches, routers, or hubs). Please refer to the following table
for cable specifications.
4-Pin Fast Ethernet Port Definition
TES-3082GT-M12-BP1
TES-3082GT-M12-BP1
1907-2-29-TES3082GTM12-1.0
Switch
EN50155
EN50155 10-port managed
Ethernet switch
I N D U S T R I A L
65.0
1
Instead of screwing the screws in all the way, it is advised to
leave a space of about 2mm to allow room for sliding the
switch between the wall and the screws.
The switch uses the M12 A-coded 5-pin male connector on
the front panel for relay output. Use a power cord with an
M12 A-coded 5-pin female connector to connect the relay.
The relay contacts will detect user-configured events and
form an open circuit when an event is triggered.
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
4-pin female M12
D-coding connector
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
4-pin female M12
D-coding connector
1000BASE-T
Cat. 5/Cat. 5e 100-ohm UTP
UTP 100 m (328ft)
4-pin female M12
D-coding connector
*2 (GxA & GxB)
For pin assignments of the LAN ports, please refer to the following tables.
QIG
1
170.1
196.0
R2.5
R4.00
155.8
75.0
21.3
15.0
6.50
178.0
151.6
132.1
G1B
G1A
G2B
G2A
Power
Failure
Bypass
P1
P5
P2
P6
P3
P7
P4
P8
LNK/ACT
DPX/COL
V1+
V1-
V2+
V2-
Power
Console
N.C.
RXD
RS-232, 9600bps, 8, N, 1
GND
TXD
N.C.
3A@24VDC
Relay
N.C.
Relay Output
Fault
Ring
R.M.
PWR2
PWR1
TES-3082GT-M12-BP1
LNK/ACT
DPX/COL
LNK/ACT
DPX/COL
LNK/ACT
DPX/COL
GxA
GxB
LNK/ACT
100M
Tx+
Rx+
Tx-
Rx-
DA+
DB+
DA-
DB-
DC+
DD+
DC-
DD-
P1~P8
Power
Failure
Bypass
LNK/ACT
100M
Reset
G1B
G1A
G2B
G2A
Power
Failure
Bypass
P1
P5
P2
P6
P3
P7
P4
P8
LNK/ACT
DPX/COL
V1+
V1-
V2+
V2-
Power
Console
N.C.
RXD
RS-232, 9600bps, 8, N, 1
GND
TXD
N.C.
3A@24VDC
Relay
N.C.
Relay Output
Fault
Ring
R.M.
PWR2
PWR1
TES-3082GT-M12-BP1
LNK/ACT
DPX/COL
LNK/ACT
DPX/COL
LNK/ACT
DPX/COL
GxA
GxB
LNK/ACT
100M
Tx+
Rx+
Tx-
Rx-
DA+
DB+
DA-
DB-
DC+
DD+
DC-
DD-
P1~P8
Power
Failure
Bypass
LNK/ACT
100M
Reset
7
8
9
10
12
15
2
3
4
6
5
11
14
13
2
Tx+
1
Rx+
Tx-
4
Rx-
3
Pin No.
Description
#1
RD+
#2
TD+
#3
RD-
#4
TD-
4-Pin Gigabit Port Definition
GxA
GxB
2
DA+
1
DB+
DA-
4
DB-
3
2
DC+
1
DD+
DC-
4
DD-
3
Configurations
After installing the router and connecting cables, start the
evice by turning on
power. The green power LED should turn on. Please refer to the following tablet
for LED indication.
d
Pin No.
GxA Description
#1
DB+
#2
DA+
#3
DB-
#4
DA-
Pin No.
GxB Description
#1
DD+
#2
DC+
#3
DD-
#4
DC-
