Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
a r e l a y e r 2 m a n a g e d
E t h e r n e t s w i t c h e s w i t h
I G S - 9 0 8 4 G P - L A
8x10/100/1000Base-T(X) ports and 4x100/1000Base-X SFP ports. The
switches support Ethernet Redundancy protocol, O-Ring (recovery time <
30ms over 250 units of connection) and MSTP (RSTP/STP compatible) can
protect your mission-critical applications from network interruptions or
temporary malfunctions with its fast recovery technology. And support wide
operating temperature from -40 C to 75 C.
can also be
o
o
IGS-9084GP-LA
managed centralized and convenient by Open-Vision, Except the Web-
based interface, Telnet and console (CLI) configuration.
Therefore, the
switch is one of the most reliable choice for highly-managed and Fiber
Ethernet application.
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Reduced Air Flow:
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Safety & Warnings
Dimension
Panel Layouts
1. PWR indicators
2. Faulty relay indicator
3. R.M. status LED
4. Ring status LED
5. Reset button
6. Link/Act LED for Gigabit LAN
ports
7. Gigabit LAN ports
8. Speed LED for Gigabit LAN ports
9. Console port
10. SFP Ports
Package Contents
Contents
DIN-rail Kit
CD
IGS-9084GP-LA
Pictures
Number
X 1
X 1
X 1
Front View
Top Panel
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
QIG
Console Cable
X 1
X 1
X 1
Wall-mount Kit
Rear View
1
2
1
1. Wall-mount screw holes
2. Din-rail screw holes
1. Terminal blocks: PWR1, PWR2
, Relay
2. Ground wire.
1
Installation
Step 1:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in
the middle of the back panel.
Step 2:
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch
clicks into the rail firmly.
DIN-rail Installation
Step 1:
Screw the wall-mount kit onto the rear panel of the switch. A total of six
screws are required, as shown below.
Step 2:
Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Step 3:
Insert a screw head through the large parts of the keyhole-shaped apertures,
and then slide the switch downwards. Tighten the screws for added stability.
Wall-mounting
IGS-9084GP-LA
Q I G
IGS-9084GP-LA
1907-2-29-IGS9084GPLA-1.0
Mechanical Loading:
Mounting of the equipment in the rack should be such that a
hazardous condition is not achieved due to uneven mechanical loading.
Circuit Overloading:
Consideration should be given to the connection of the equipment
to the supply circuit and the effect that overloading of the circuits might have on overcurrent
protection and supply wiring. Appropriate consideration of equipment nameplate ratings
should be used when addressing this concern.
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3,4,5,5e UTP cables to connect to any other network devices (PCs, servers,
switches,
routers,
or
hubs).
Please
refer
to
the
following
table
for
cable
specifications.
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1000BASE-T
Cat. 5 / Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
GIGABIT
I N D U S T R I A L
SWITCH
Industrial Managed Gigabit Switch
IGS-9084GP-LA
G11
100/1000X
PWR
10/100/1000T
G9
PWR1
PWR2
Fault
G6
G8
G2
G4
LNK/ACK
Speed
G5
G7
G1
G3
G12
G10
Console
Ring
R.M
Reset
IGS-9084GP-LA
G11
100/1000X
PWR
10/100/1000T
G9
PWR1
PWR2
Fault
G6
G8
G2
G4
LNK/ACK
Speed
G5
G7
G1
G3
G12
G10
Console
Ring
R.M
Reset
7
2
3
4
5
6
1
8
9
10
2
IGS-9084GP-LA
G11
100/1000X
PWR
10/100/1000T
G9
PWR1
PWR2
Fault
G6
G8
G2
G4
LNK/ACK
Speed
G5
G7
G1
G3
G12
G10
Console
Ring
R.M
Reset
Unit =mm (Tolerance ±0.5mm)
