IGS-9080
PWR
PWR1
PWR2
R.M
Ring
Fault
10/100/
1000T
G3
G4
G1
G2
G7
G8
G5
G6
Reset
Quick Installation Guide
Version 1.0
Q
uick
I
nstallation
G
uide
Introduction
PRINTED ON RECYCLED PAPER
The
is a managed industrial Ethernet switch with eight
10/100/1000Base-T(X) ports. The series consists of the
and
models to meet different application needs. The former
supports IEEE 1588v2 clock synchronization while the latter does not.
The switch supports Ethernet Redundancy protocol, O-Ring (recovery time
< 30ms over 250 units of connection) and MSTP (RSTP/STP compatible) to
protect mission-critical applications from network interruptions or
temporary malfunctions with fast recovery technology. With a wide
operating temperature from -40 C to 70 C, the device can be managed
centrally via ORing’s proprietary Open-Vision platform as well as via Web-
based interfaces, Telnet, and console (CLI). The switch is one of the most
reliable choices for highly-managed and fiber Ethernet applications.
IGS-9080 series
IGPS-9080
IGPS-9080-NP
o
o
Preparation
Before you begin installing the switch, make sure you have all of the package
contents available and a PC with Microsoft Internet Explorer 6.0 or later, for
using web-based system management tools.
Elevated Operating Ambient:
Reduced Air Flow:
Mechanical Loading:
If installed in a closed or multi-unit rack
assembly, the operating ambient temperature of the rack environment may be
greater than room ambient. Therefore, consideration should be given to
installing the equipment in an environment compatible with the maximum
ambient temperature (Tma) specified by the manufacturer.
Installation of the equipment in a rack should be such
that the amount of air flow required for safe operation of the equipment is
not compromised.
Mounting of the equipment in the rack should be
such that a hazardous condition is not achieved due to uneven mechanical
loading.
Safety & Warnings
Dimension
Panel Layouts
11
1. Reset button
2. PWR status LED
3. PWR1 LED
4. PWR2 LED
5. R.M. status LED
6. Ring status LED
7. Faulty relay indicator
8. Console port
9. Port speed LED
10. Port link LED
11. Gigabit Ethernet ports
Package Contents
Contents
DIN-rail Kit
CD
IGS-9080 /
IGS-9080-NP
Pictures
Number
X 1
X 1
X 1
Front View
Top Panel
The device is shipped with the following items. If any of these items is
missing or damaged, please contact your customer service representative for
assistance.
GIGABIT
I N D U S T R I A L
SWITCH
Industrial Managed Gigabit Switch
QIG
Console Cable
X 1
X 1
X 1
Wall-mount Kit
10
Rear View
1
2
1
1. Wall-mount screw holes
2. Din-rail screw holes
1. Terminal blocks: PWR1, PWR2
(12-48V DC), Relay
1
Installation
Step 1:
Step 2:
Slant the switch and screw the Din-rail kit onto the back of the switch, right in
the middle of the back panel.
Slide the switch onto a DIN-rail from the Din-rail kit and make sure the switch
clicks into the rail firmly.
DIN-rail Installation
Step 1:
Step 2:
Step 3:
Screw the wall-mount kit onto the rear panel of the switch. A total of six
screws are required, as shown below.
Use the switch, with wall mount plates attached, as a guide to mark the
correct locations of the four screws.
Insert a screw head through the large parts of the keyhole-shaped apertures,
and then slide the switch downwards. Tighten the screws for added stability.
Wall-mounting
IGS-9080 Series
Q I G
IGS-9080
1907-2-29-IGS9080-1.0
Circuit Overloading:
Consideration should be given to the connection of the
equipment to the supply circuit and the effect that overloading of the circuits might have
on overcurrent protection and supply wiring. Appropriate consideration of equipment
nameplate ratings should be used when addressing this concern.
9
Network Connection
The switch provides standard Ethernet ports. According to the link type, the switch uses
CAT 3,4,5,5e UTP cables to connect to any other network devices (PCs, servers,
switches, routers, or hubs). Please refer to the following table for cable
specifications.
Cable Types and Specifications:
Cable
Type
Max. Length
Connector
10BASE-T
Cat. 3, 4, 5 100-ohm
UTP 100 m (328 ft)
RJ-45
100BASE-TX
Cat. 5 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
1000BASE-T
Cat. 5 / Cat. 5e 100-ohm UTP
UTP 100 m (328 ft)
RJ-45
54.3
32.2
45.0
14.0
40.0
50.0
25.3
33.6
12.5
54.3
145.1
108.5
32.0
32.2
11
6
.0
18.0 18.15
51.0
209.3
7.35
187.4
R2.5
R3.95
46.0
IGS-9080
PWR
PWR1
PWR2
R.M
Ring
Fault
10/100/
1000T
G3
G4
G1
G2
G7
G8
G5
G6
Reset
8
2
3
4
5
6
7
1
IGS-9080
PWR
PWR1
PWR2
R.M
Ring
Fault
10/100/
1000T
G3
G4
G1
G2
G7
G8
G5
G6
Reset
