Origin live THE RESOLUTION CLASSIC Скачать руководство пользователя страница 5 | Manualshive

Страница: 5 / 23

Origin live THE RESOLUTION CLASSIC Скачать руководство пользователя страница 5

5

Parts list & tools required

Parts supplied

Ultra plinth, 4 small rubber feet

Lid, (usually fitted with 2 off Lid hinges bottom & 2 top, 4 off M4 x 10mm bolts, 4 off M4 nuts.

Bag – Belt, Oil, 1 off arm cable clip (large), 1 off motor cable clip (small), 2 off no 6 x •” screws, arm packing ring
(unless sliding vta is fitted). 2 off cork feet

Bag - 3 springs / 3 long M5 x 80 bolts / 3 spring seats / 3 rubber washers / 6 off M5 washers / 9 off M5 serrated
washers / 6 off M5 nuts / 4 off large w 2 on transit bolts

Platter

Sub-chassis

( MDF damper arm & spring plates, glued washers), Main bearing house on sub-chassis, Sub-platter

Motor with fitted pulley – (attached)

Switch box

Power supply 230 volt or 110 volt (delete one)

Upgrade Transformer (optional)

Sliding VTA adjuster, Aluminium sleeve, allen set screw (optional)

Threaded VTA adjuster and packing washer (optional)

Arm (optional)

Paperwork

Turntable instructions

Strobe card

Tools you will need ideally

Ruler or measuring tape

Marker pen.

Small hacksaw or powerful snips

Cross head screwdriver

3mm or 3.5mm drill

Pliers or molegrips

Hammer

Soldering iron (not essential)

Spirit level

«
...
3
4
5
6
7
...
»

Содержание THE RESOLUTION CLASSIC
























Отзывы:

Нет отзывов