Orientalmotor BXII Series Скачать руководство пользователя страница 9

Страница: 9 / 52

Installation and connection of the OPX-2A

−9−

4.3 Connecting to the driver

Plug the connector attached to the end of the

OPX-2A

cable into the data edit connector (CN6) on the driver, and

then turn on the power to the driver.

Data edit connector

(CN6)

Note

•

When operation data and parameters are set on the

OPX-2A

, they will be stored in the driver.

Once stored in the driver, the data will not be cleared even after the

OPX-2A

is disconnected

from the driver.

•

Turning on the power to the driver will also turn on the power to the

OPX-2A

. Turning off the

driver power will turn off the

OPX-2A

power.

•

Turn off the driver power before connecting or disconnecting the

OPX-2A

cable.

4.4 Error display on

OPX-2A

screen

The following error message is displayed on the

OPX-2A

screen.

Error display

Description

Remedial action

A communication error occurred

between the

OPX-2A

and driver.

•

Check if the

OPX-2A

is connected securely.

•

Check if the

OPX-2A

cable is disconnected or

damaged.

•

The

OPX-2A

or the communication part of the driver

may have damaged. Contact your nearest Oriental

Motor sales office.

Содержание BXII Series





















































Результаты поиска

Содержание BXII Series

Отзывы:

Orientalmotor BXII Series, Руководство по эксплуатации, Страница: 9 / 52

Результаты поиска

Содержание BXII Series

Отзывы: