Orientalmotor BXII Series Скачать руководство пользователя страница 25

Страница: 25 / 52

When using the product with the speed control mode

−25−

5.6 Copy mode

The

OPX-2A

has four data banks, and operation data and parameters can be saved in each of these data banks. Since

non-volatile memory is used as the data memory element, stored data will be retained even after the power is turned

off.

In the copy mode, the data saved in the

OPX-2A

can be downloaded to the driver. Meanwhile, the data saved in the

driver can be uploaded to the

OPX-2A

It is also possible to verify data in the

OPX-2A

against the corresponding data in the driver, or restore driver data to

their initial values.

Overview of the copy mode

•

Download

Data saved in the

OPX-2A

can be copied to the driver.

•

Upload

Data saved in the driver can be copied to the

OPX-2A

•

Verification

Data in the

OPX-2A

can be verified against the corresponding data in the driver.

•

Initializing driver data

Data saved in the driver can be restored to their initial values.

Operation in the copy mode

1. Use the

key to select the copy mode.

2. Press the

key on the top screen in the copy

mode.

3. Use the

keys to select the item you want

to perform.

Download

Verification

Upload

Initializing

Top screen in

the copy mode

•

What happens when the

key is pressed while the motor is operating

During operation, if the

key is pressed on the lower level of the top

screen in the copy mode, an error will occur, thereby displaying "oPE-Err."

Be sure to stop the motor operation before pressing the

key.

•

What happens when the

key is pressed while the edit lock function is enabled

While the edit lock function is enabled, the screen cannot change to any lower

level from the top screen of the copy mode. Pressing the

key will

generate an error, thereby displaying "LocK-Err."

Be sure to cancel the edit lock function before pressing the

key.

Refer to p.7 for the procedure to cancel the edit lock function.

Note

Stop the motor operation before changing to the copy mode.

Содержание BXII Series





















































Результаты поиска

Содержание BXII Series

Отзывы:

Orientalmotor BXII Series, Руководство по эксплуатации, Страница: 25 / 52

Результаты поиска

Содержание BXII Series

Отзывы: