background image

3

3.  Installation

Installation conditions

Install the motor and capacitor in a location that meets the following conditions.

Using the motor and capacitor in a location that does not satisfy these conditions could damage it.

Indoors

Ambient temperature : ‒10°C (14°F) ~ +40°C (104°F) (avoid freezing)

 

(‒10°C (14°F) ~ +50°C (122°F) for 100/200V)

Ambient humidity: 85% max. (avoid condensation)

Not exposed to explosive, flammable, or corrosive gases

Not exposed to direct sunlight

Not exposed to dust

Not exposed to water or oil

A place where heat can escape easily

Not exposed to continuous vibration or excessive impact

1000m or less above sea level

3. 1 Install the motor

1) Assembling the Motor and Gearhead (For only separate type)

Use the gearhead of the 

BH6G2

 type. Confirm gearhead compatibility by checking the table in section 

2. 2

.

For the detail of assembling the motor and gearhead, see the operating manual of gearhead.

2) Installing the motor

Combination type, pinion shaft motor (separate type)

Parallel shaft type

Motor

Mounting plate

Washers

Spring washers

Hexagonal nuts

Mounting screws
(M8 hexagonal 
socket-head screws)

Drill holes in the mounting plate and fasten the motor to the mounting plate with

the provided mounting screws, hexagonal nuts, washers and spring washers.

Be sure that no gaps are left between the gearhead and the surface of the

mounting.

Mounting plate thickness is 10mm (0.393in.) when using the provided

mounting screws.

Right angle type

Motor

Mounting plate

Screws

Gearhead

Washers

Nuts

Drill holes in the mounting plate and fasten the motor to the mounting plate with

screws, nuts, and washers (The mounting screws are not provided.). Be sure

that no gaps are left between the motor and the surface of the mounting plate.

∗ 

Illustration shows 

BH6G2-

RH

.

Note

 

 For 

BH6G2-

RH

, when using the gearhead flange to mount the

 

  gearhead to equipment, proper alignment between the hollow shaft

 

  inside dimension and the load shaft is necessary.

 

 The diameter of the boss of the shaft is Ø58h8, use it as a guide for

 

  proper alignment.

Flange surface

Load shaft

Gearhead

Round shaft motor

Mounting screws

Mounting plate

Motor

Washers

Nuts

Drill holes in the mounting plate and fasten the motor to the mounting plate with

screws, nuts, and washers (The mounting screws are not provided.). Be sure

that no gaps are left between the motor and the surface of the mounting plate.

Mounting screws

Screw size

Tightening torque

M8

6.0N·m (53lb-in)

Note

  Do not insert the motor into the mounting hole at an angle or force it in,

 

as this may scratch the flange pilot section and damage the motor.

3) Cooling fan

When installing a motor with a cooling fan onto a device, leave 10mm (0.393in.) or more behind the fan cover or open a ventilation hole so

that the cooling inlet on the back of the motor cover is not blocked.

3. 2 Mounting the capacitor (For only single-phase motors)

 

Ø4.3

(.169DIA.)

Before mounting the provided capacitor, check that the capacitor’s capacitance matches that stated on the motor’s

name plate.

Use M4 screws to mount the capacitor (screws not provided).

 Dimensions in millimeters (inch).

Note

 

  Do not let the screw fastening torque exceed 1N·m (8.8lb-in) to prevent damage to the mounting feet.

 

  Mount capacitor at least 10cm (3.94in.) away from the motor. If it is located closer, the life of the capacitor

 

  will be shortened.

Содержание BH Series










Отзывы: