Oriental motor NETC01-M3 Скачать руководство пользователя страница 11

Страница: 11 / 62

Connection

−11−

5 Connection

This chapter explains the connection method of the

NETC01-M3

and power supply/communication cable,

as well as the grounding method.

5.1 Connection example

RS-485 communication cable

MECHATROLINK-

䊢

communication cable

24 VDC

GND

Power supply connector (CN1)

MECHATROLINK-

䊢

communication connector (CN2-1)

RS-485 communication

connector (CN6)

Data edit connector (CN3)

OPX-2A

Use the

OPX-2A

MEXE02

to set parameters.

MEXE02

Use the accessory communication

cable for the data setting software

when connecting the PC and

NETC01-M3

5.2 Connecting the power supply and grounding the

NETC01-M3

Connecting the power supply

Connect the power supply cable (AWG22: 0.3 mm

) to the power supply connector (CN1) of the

NETC01-M3

using the supplied CN1 connector (3 pins).

Grounding the

NETC01-M3

Ground the Frame Ground terminal (FG) of the

NETC01-M3

as necessary.

Ground using a wire of AWG24 to 16 (0.2 to 1.25 mm

), and do not share the protective earth terminal with

a welder or any other power equipment.

CN1 connector pin assignments

Pin No.

Signal name

Description

+24 VDC

+24 VDC 0.2 A or more

GND

Power supply GND

Frame Ground

Note

•

When connecting, pay attention to the polarity of the power supply. Reverse-polarity connection may
cause damage to the

NETC01-M3

•

Do not wire the power supply cable of the

NETC01-M3

in the same cable duct with other power

lines. Doing so may cause malfunction due to noise.

Содержание NETC01-M3































































Результаты поиска

Содержание NETC01-M3

Отзывы:

Похожие инструкции для NETC01-M3

Бренды по названию

Популярные бренды

Oriental motor NETC01-M3, Руководство пользователя

Результаты поиска

Содержание NETC01-M3

Отзывы:

Похожие инструкции для NETC01-M3

Бренды по названию

Популярные бренды