Oracle X7-8 Скачать руководство пользователя страница 64

Страница: 64 / 308

Troubleshooting Using Status Indicators

Call

Out

Status LED or

Button

Icon and Color

Description

Fault-Service

Required

Amber

Indicates a fault state in a fan module:

■ Off – Fan module is operating normally,
■ Steady On – A fault is present in the fan module.

Green

Indicates the functional state of the fan module:

■ Off – Fan module is powered off or functioning abnormally.
■ Steady On – Fan module is powered on and functioning normally.

Power Supply (PS) Indicators

Each power supply (PS) has three indicators arranged in a single row from left to right. Power

supplies for System A are PS2 and PS3. Power supplies for System B are PS0 and PS1.

Oracle Server X7-8 Service Manual • October 2017

Содержание X7-8





















































































































































































































































































































Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды

Oracle X7-8, Руководство по обслуживанию

Результаты поиска

Содержание X7-8

Отзывы:

Бренды по названию

Популярные бренды