Oracle X7-2 Скачать руководство пользователя страница 90

Страница: 90 / 148

Test the IPv4 or IPv6 Network Configuration

set /SP/network/ipv6 state=

enabled

disabled

pending_static_ipaddress=

value

subnet_mask_value

pending_static_ipgatewayaddress=

value

Note -

A dual-stack network connection is enabled when both the IPv4 and IPv6 State

properties are set to enabled. By default, Oracle ILOM is factory-configured with network

settings enabled for a dual stack (IPv4 and IPv6) network connection. If the IPv4 State property

is enabled (

SP/network state=enabled

), and the IPv6 State property is disabled (

SP/network

state=disabled

), Oracle ILOM supports an IPv4-only network connection.

To commit the IPv4 and IPv6 pending network changes in Oracle ILOM,

type:

set /SP/network commitpending=true

Note -

All user sessions on the SP are terminated upon committing the IP network property

changes. To log back in to Oracle ILOM, use the newly assigned service processor IP address.

Test the IPv4 or IPv6 Network Configuration

Use either the Oracle ILOM web interface or CLI to test the IPv4 or IPv6 network

configuration.

■

From the Oracle ILOM web interface:

Click ILOM Administration → Connectivity → Network.

Oracle Servers X7-2 and X7-2L Installation Guide • October 2017

Содержание X7-2





















































































































































Результаты поиска

Содержание X7-2

Отзывы:

Oracle X7-2, Руководство по установке, Страница: 90 / 148

Результаты поиска

Содержание X7-2

Отзывы: