Oracle X5-4 Скачать руководство пользователя страница 16

Страница: 16 / 358

Server Overview

Server Overview

The Oracle Server X5-4 is a 3RU rack-mount server system. The following table lists the

server-supported components.

Component

Description

Processor (CPU)

Intel Xeon® E7-8895 v3 18-core 2.6 GHz processor.

Supported configurations:

■ Two processors installed in sockets 0 and 1
■ Four processors installed in sockets 0 through 3

Memory

Up to eight memory riser cards are supported (two risers per CPU) in the server chassis. Each

memory riser supports up to twelve DDR3-1600 ECC low-voltage registered or load-reduced

DIMMs, allowing up to twenty-four DIMMs per processor. Installed DIMMs must be the

same type and size.

■

In a two CPU system

, you can install up to a maximum of 1.5 TB of system memory.

■

In a four CPU system

, you can install up to a maximum of 3 TB of system memory.

For information on supported DIMM configurations, see

“Supported DIMMs and DIMM

Population Rules” on page 157

Storage devices

For internal storage, the server chassis provides:

■ Six 2.5-inch drive bays, accessible through the front panel.

All bays can be populated with SAS-3 HDDs or SSDs.
Four of the six drive bays (2 through 5) can also support NVMe SSD drives.

Note -

NVMe drive support requires the purchase an optional PCIe NVMe Switch card

during the initial factory order of the server. It cannot be added later.

■ An optional tray-load DVD+/-RW drive on the front of the server, below the drive bays.
■ Oracle Storage 12 Gb/s SAS RAID PCIe HBA, Internal.

This card supports RAID levels 0, 1, 5, 6, 10, 50, and 60, with a minimum of 1 Gb

data cache, and Battery Backed Write Cache (BBWC) using an ESM (Energy Storage

Module).

USB 2.0 ports

■ Four external high-speed USB ports: two in front and two in back.
■ Two internal high-speed USB ports on the motherboard.

One internal port holds the optional factory-installed Oracle System Assistant (OSA)

flash drive. A second internal port can hold a USB flash drive for system booting.

VGA ports

Two high-density DB-15 video ports: one in front and one in back.

The server includes an embedded VGA 2D graphics controller with 8 MB supporting

resolutions up to 1600 x 1200 x 16bits @ 60 Hz (1024 x 768 when viewed remotely using

Oracle ILOM RKVMS).

Note -

The back VGA port supports VESA Device Data Channel for monitor identification.

PCIe 3.0 I/O slots

Eleven PCIe 3.0 slots that accommodate low-profile PCIe cards.

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды