Oracle X5-4 Скачать руководство пользователя страница 102

Страница: 102 / 358

Power Off the Server Using the Server OS

■

“Power Off, Immediate (Power Button)” on page 103

■

“Power Off, Remote (Oracle ILOM CLI)” on page 104

■

“Power Off, Remote (Oracle ILOM Web Interface)” on page 105

■

“Remove Power” on page 106

Power Off the Server Using the Server OS

If the server OS is running, you can use the OS shutdown procedure to power off the server to

standby power mode. The OS shutdown procedure provides a graceful shutdown of the server.

To power off the server, use the OS-specific shutdown procedure.

See Also

■

“Power Subsystem” on page 28

Power Off, Graceful (Power Button)

Note -

This procedure is performed locally and requires access to the server front panel.

Powering off the server by pressing the front panel Power button causes operating systems with

Advanced Configuration and Power Interface (ACPI) to perform an orderly shutdown of the

OS. Non-ACPI enabled operating systems might ignore this event and not shut down the host.

If your OS ignores this event, shut down the server using the server OS or Oracle ILOM.

Use this procedure to perform a graceful power off and place the server in standby power mode.

To power off the server gracefully, press and

immediately

release the front panel

Power button.

102

Oracle Server X5-4 Service Manual • December 2015

Содержание X5-4







































































































































































































































































































































































Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды

Oracle X5-4, Руководство по обслуживанию

Результаты поиска

Содержание X5-4

Отзывы:

Похожие инструкции для X5-4

Бренды по названию

Популярные бренды