manualshive.com logo in svg

Oracle Tekelec 1200, Руководство по установке

Поделиться
Скачать
Oracle Tekelec 1200 Скачать руководство пользователя страница 62

Recommended Tools

Tekelec tools should be labeled “Property of TEKELEC” with either a press-on Field Tool Identification
label or Field Tool Identification wrap.

• Safety glasses

• Power knife

• Cable cutters

• Cable stripper

• Flush cutters

• Crimping tool with embossing dies (test before using)

• Socket wrench set, 1/4-inch or 3/8-inch drive or open-end wrenches

• Non oxidizing grease

Note:  It is a requirement that when mating dissimilar metals non oxidizing grease is used between
them as a corrosion inhibitor.

• Lacing cord and nylon cable ties

• Heat-shrink gun (hot air blower)

• Torque wrench

• Fiber paper

Procedure — Ground Frame

1. Install the continuous ground conductor to the Ground Window. Run the conductor the length of

the equipment lineup (see the figure System Frame Grounding).

The separate #6 American Wire Gauge (AWG) cable ground that runs to each frame will allow
removal of a frame from the lineup without interrupting the grounding of other frames in the
lineup.

2. Install the branch ground conductor to the frame ground cable (P/N 830-1354-01, Cable

Assy_6AWG_Frame Ground_GRN with YEL Stripe) pre-attached to the Frame Bus Bar. Use H-tap
to connect this cable to the branch ground conductor.

The continuous aisle ground conductor will be H-tapped to the branch (see the figure System Frame
Grounding). Torque screws to 45 inch-pounds.

62

910-5681-001 Revision E, February 2014

Cabinet Installation

Installation

Содержание Tekelec 1200













































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды