Oracle Sun Server X4-4 Скачать руководство пользователя страница 143

Страница: 143 / 148

Troubleshooting Installation Issues

This section provides information to aid in troubleshooting installation issues with your server.

Description

Links

Learn about troubleshooting and diagnostic reference

information.

“Troubleshooting and Diagnostic

References” on page 143

Record server information before contacting Service.

“Technical Support Information

Worksheet” on page 143

Locate the system serial number before contacting

Service.

“Locating the Server Serial Number” on page 144

Troubleshooting and Diagnostic References

The

Sun Server X4-4 Service Manual

provides product-specific information about

troubleshooting problems, see

“Troubleshooting and Diagnostics” in

Sun Server X4-4 Service

Manual

The

Oracle x86 Server Diagnostics Guide

(

http://www.oracle.com/goto/x86AdminDiag/

docs

) provides information about a wide variety of tools available for Oracle's x86 servers.

Knowledge articles, white papers, and product updates are available through the Oracle Support

portal:

https://support.oracle.com

Technical Support Information Worksheet

If the troubleshooting information fails to solve your problem, use the following table to collect

information that you might need to communicate to the support personnel.

Troubleshooting Installation Issues

143

Содержание Sun Server X4-4





















































































































































Результаты поиска

Содержание Sun Server X4-4

Отзывы:

Oracle Sun Server X4-4, Руководство по установке, Страница: 143 / 148

Результаты поиска

Содержание Sun Server X4-4

Отзывы: