manualshive.com logo in svg

Oracle Sun Server X4-4, Руководство по установке, Страница: 136 / 148

Поделиться
Скачать
Oracle Sun Server X4-4 Скачать руководство пользователя страница 136

Use the Power Button for Orderly Shutdown

■

“Use the Oracle ILOM CLI for Orderly Shutdown” on page 137

■

“Use the Oracle ILOM Web Interface for Orderly Shutdown” on page 137

Use the Power Button for Orderly Shutdown

1.

Momentarily press and release the Power button [1] on the front panel.

This causes Advanced Configuration and Power Interface (ACPI)-enabled operating systems to

perform an orderly shutdown. Servers not running ACPI-enabled operating systems will shut

down to standby power mode immediately.

Callout

Description

1

Power button

Once main power shuts down, the system goes into standby mode. The system OK indicator

blinks in standby power mode.

2.

To completely power off the server from standby power mode, disconnect the

power cables from the server.

The server powers down completely.

See Also

■

“Front Panel Features” on page 15

■

“Use the Oracle ILOM CLI for Orderly Shutdown” on page 137

■

“Use the Oracle ILOM Web Interface for Orderly Shutdown” on page 137

■

“Use the Power Button for Immediate Shutdown” on page 138

136

Sun Server X4-4 Installation Guide • October 2015

Содержание Sun Server X4-4





















































































































































Отзывы:

Нет отзывов