Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 41 / 258

Server Fault Remind Button Operation

Clearing a fault with the

fmadm

aquit

command does not clear that fault in the Oracle

Enterprise Manager Ops Center software. You must manually clear the fault or incident. For

more information, refer to

Oracle Enterprise Manager Ops Center Feature Reference Guide

at:

http://www.oracle.com/pls/topic/lookup?ctx=oc122

If you are servicing a component, return to the procedure for that component.

Related Information

■

“Checking for Faults” on page 25

■

“Performing Advanced Troubleshooting” on page 34

Server Fault Remind Button Operation

When you press the server Fault Remind button, an LED located next to the Fault Remind

button lights green to indicate that there is sufficient voltage present in the fault remind circuit

to light any fault LEDs that were lit due to a component failure. If this LED does not light when

you press the Fault Remind button, it is likely that the capacitor powering the fault remind

circuit has lost its charge. This can happen if the Fault Remind button is pressed for several

minutes with fault LEDs lit or if power has been removed from the server for more than 15

minutes.

Fault LEDs are provided on the motherboard for DIMMs. The figure shows the location of the

Fault Remind button and LED.

Detecting and Managing Faults

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды