Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 31 / 258

Interpreting LEDs

Front Panel LEDs

No.

LED

Description

Alarm LEDs:
■ Critical Alarm LED (red)

Indicates a critical alarm condition.

■ Major Alarm LED (red)

Indicates a major alarm condition.

■ Minor Alarm LED (amber)

Indicates a minor alarm condition.

■ User Alarm LED (amber)

Indicates a user alarm condition.

Rear PS Status LED (amber)

Indicates the state of the power supplies:

■

Off

– Steady state, no service action is required.

■

– Fault with one of the power supplies.

SP Status LED

Indicates the state of the SP:

■

Green flashing

–SP is booting.

■

Green steady

–SP booted and OK , no service action is required.

OK LED (green)

Indicates these conditions:

■

Off

– Server is not running in its normal state. Server power might be off. The SP

might be running.

■

Steady on

– Server is powered on and is running in its normal operating state. No

service actions are required.

■

Fast blink

– Server is running in Standby mode and can be quickly returned to full

function.

■

Slow blink

– Normal but transitory activity is taking place. Slow blinking might

indicate that system diagnostics are running or that the server is booting.

Detecting and Managing Faults

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды