Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 231 / 258

Install the Motherboard

■

“Preparing for Service” on page 43

■

“Returning a Server to Operation” on page 235

Install the Motherboard

Installing the motherboard is a cold-service operation. You must power off the server before

installing the motherboard.

Position the motherboard for installation into the server.

The heatsinks are toward the front of the server, and the ports are at the rear.

Lift the motherboard by the handles, and slowly lower the motherboard into the

chassis.

Caution -

Take care when using the handles to install the motherboard. These handles are not in

weight-balanced locations. Avoid flexing the motherboard.

Caution -

Take care to clear the four screws at the rear of the chassis. The screws are long and

might scratch or damage the motherboard.

Servicing the Motherboard

231

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды