Oracle Netra SPARC S7-2 Скачать руководство пользователя

Страница: 131 / 258

Servicing Power Supplies

The power supplies apply AC or DC facility power for use in the server chassis. The power

supplies are configured for redundancy and are stacked at the rear left of the server. See

“Component Locations (Storage, Power, NVMe, and Fan Modules)” on page 14

Note -

Typically servers are ordered and installed specifically for either AC or DC power-based

systems. AC and DC servers cannot be mixed into the same system. It is possible to convert a

server's power supply from either AC to DC or DC to AC. However, the server's installation

must be in a system that matches the power supply. For more information, refer to

Netra SPARC

S7-2 Server Installation Guide

Description

Links

Replace a faulty power supply.

“Locate a Faulty Power Supply” on page 132

“Power Supply LEDs” on page 132

“Remove a Power Supply” on page 134

“Install a Power Supply” on page 137

“Verify a Power Supply” on page 138

Remove a power supply as part of another

component's service operation.

“Remove a Power Supply” on page 134

Install a power supply as part of another

component's service operation.

“Install a Power Supply” on page 137

Add additional power supplies.

“Install a Power Supply” on page 137

“Verify a Power Supply” on page 138

Decrease the number of existing power

supplies.

“Remove a Power Supply” on page 134

Identify a faulty power supply.

“Power Supply LEDs” on page 132

“Locate a Faulty Power Supply” on page 132

“Detecting and Managing Faults” on page 25

Servicing Power Supplies

131

Содержание Netra SPARC S7-2



































































































































































































































































Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды

Oracle Netra SPARC S7-2, Руководство по обслуживанию

Результаты поиска

Содержание Netra SPARC S7-2

Отзывы:

Похожие инструкции для Netra SPARC S7-2

Бренды по названию

Популярные бренды