Oracle DE2-24 Скачать руководство пользователя страница 134

Страница: 134 / 312

How to Replace a ZS3-2 Power Supply

How to Replace a ZS3-2 Power Supply

Storage controllers are equipped with redundant hot-swappable power supplies. If a power

supply fails and you do not have a replacement, leave the failed power supply installed to

ensure proper air flow. A faulted power supply is indicated by an amber colored status LED.

Use the following procedure to replace a ZS3-2 power supply.

Gain access to the rear of the storage controller where the faulted power supply

is located.

If a cable management arm (CMA) is installed, press and hold the CMA release

tab and rotate the arm out of the way.

Disconnect the power cord from the faulted power supply.

Press the release tab to the left and pull on the handle.

134

Oracle ZFS Storage Appliance Customer Service Manual • February 2016

Содержание DE2-24

























































































































































































































































































































Результаты поиска

Содержание DE2-24

Отзывы:

Бренды по названию

Популярные бренды

Oracle DE2-24, Руководство по обслуживанию клиентов

Результаты поиска

Содержание DE2-24

Отзывы:

Бренды по названию

Популярные бренды