Oracle 1242 Скачать руководство пользователя страница 35

Страница: 35 / 84

Move the Rack to the Installation Site

Move the Rack to the Installation Site

The rack's front casters are fixed, so you must steer using the rear casters. You can maneuver

the rack safely by pushing it from behind.

Note -

To avoid damaging the rack, do not push on the perforated panel.

Caution -

When unpacking the rack at the installation site, verify that the leveling feet are up

before moving the rack.

Push the rack from behind to the installation site.

Caution -

Never attempt to move the rack by pushing on the side panels. Pushing on the side

panels can make the rack tip over, which can damage the equipment and cause serious personal

injury or death.

Caution -

Do not tip or rock the rack, especially if you have installed equipment into it, as the

rack can fall over.

Installing the Rack

Содержание 1242





















































































Результаты поиска

Содержание 1242

Отзывы:

Бренды по названию

Популярные бренды

Oracle 1242, Руководство пользователя

Результаты поиска

Содержание 1242

Отзывы:

Бренды по названию

Популярные бренды