OPW Installation, Operation and Maintenance Manual, Page 42 Executive Order VR-401-C
OPW Installation and Maintenance Instructions
OPW 200TG Mechanical AST Liquid Level Gauge
IMPORTANT:
Please read
these
warnings and use
the assembly instructions completely and carefully
before starting. Failure to do so may cause product
failure, or result in environmental contamination due
to liquid leakage into the soil, creating hazardous spill
conditions.
IMPORTANT:
The OPW 200TG Tank Gauges are
pre-assembled for your convenience and ease of
use. Check to make sure the unit is intact and
undamaged and all parts have been supplied. Never
substitute parts for those supplied. Doing so may
cause product failure.
WARNING-DANGER:
Using electrically operated
equipment near gasoline or gasoline vapors may
result in a fire or explosion, causing personal injury
and property damage. Be sure that the working area
is free from such hazards, and always use proper
precautions.
NOTE
: At all times when product is in the storage
tank keep the riser pipe capped, so the vapors
cannot escape into the environment.
NOTICE:
OPW products must be used in compliance
with applicable federal, state, and local laws and
regulations. Product selection should be based on
physical specifications and limitations and
compatibility with the environment and material to be
handled. All illustrations and specifications in this
literature are based on the latest production
information available at the time of publication.
Prices, materials, and specification are subject to
change at any time, and models may be discontinued
at any time, in either case, without notice or
obligation.
Standard Product Warranty
OPW warrants that products sold by it are free
from defects in materials and workmanship for a
period of one year from the date of manufacture by
OPW (ECO products two years from date of
manufacture.) Proof of purchase may be required.
As the exclusive remedy under this limited warranty,
OPW will, at its sole discretion, repair, replace, or
issue credit for future orders for any product that may
prove defective within the one-year date of
manufacture period (repairs, replacements, or credits
may be subject to prorated warranty for remainder of
the original warranty period, complete proper
warranty claim documentation required.) This
warranty shall not apply to any product that has been
altered in any way, which has been repaired by any
party other than a service representative authorized
by OPW, or when failure is due to misuse, or
improper installation or maintenance. OPW shall
have no liability whatsoever for special, incidental or
consequential damages to any party, and shall have
no liability for the cost of labor, freight, excavation,
clean up, downtime, removal, reinstallation, loss of
profit, or any other cost or charges.
For any product certified to California 2001
standards, OPW warrants that products sold by it are
free from defects in material and workmanship for a
period of one year from date of manufacture or one
year from date of registration of installation not to
exceed 15 months from date of manufacture by
OPW.
THIS WARRANTY IS IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, AND
SPECIFICALLY THE WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THERE ARE NO
WARRANTIES WHICH EXTEND BEYOND THE
DESCRIPTION ON THE FACE HEREOF.
200TG Specifications:
Accuracy:
±2 inches
Specific Gravity of Fluid:
0.65 to 1.025.
Temperature Range:
-40°F to 120°F (-40°C to 59°C)
Materials:
Enclosure/Base – Powder-Coated Aluminum,
Float – Stainless Steel,
Lens – Tempered Borosilicate,
Gears – Acetal,
Gaskets/O-rings – Nitrile,
Hardware – Stainless Steel
Torque Specifications:
Swivel Base:
80 ft-lbs maximum. (As a general rule,
hand-tighten plus 1
½
turns is adequate.)
Cover Bolts:
15-20 ft-lbs.
Lens Screws:
Tighten evenly; be careful not to over-
tighten.
Replacement Parts:
Lid Gasket:
P/N H14909M
Lens:
P/N H14358M
Float:
P/N C05165M
Cover Bolt
P/N: H14911M
