Optimum OPTIMILL MH 28V Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 60

background image

OPTIMUM

M A S C H I N E N - G E R M A N Y



20

12

Safety

Version 1.0.1 dated 30 / 08 / 2012

Page 8

Original operating instructions

MH28V

GB

WARNING!

Very serious injury due to improper use.

It is forbidden to make any modifications or alterations to the operating values of the
drilling-milling machine. These could endanger the staff and cause damage to the
drilling-milling machine.

INFORMATION

The drilling-milling machine MH28V is built according to the standard DIN EN 55011 class A.

WARNING!

The class A (machine tools) is not intended to be used in residential facilities, where
the power is supplied via a public low voltage supply system. In these areas it may
possibly be difficult to guarantee electromagnetic compatibility due to lead bound as
well as emitted interferences.

CAUTION!

If the table drilling machine is not used as intended or if the safety directives or the
operating instructions are ignored the liability of the manufacturer for any damages to
persons or objects resulting hereof is excluded and the claim under guarantee is
becoming null and void!

1.3

Reasonably foreseeable misuse

Any other use or any use beyond the use described under "Proper use" is regarded as
improper use and is forbidden.

If it is intended to use the device in any other way as described above, it is necessary to con-
sult the manufacturer.

It is only allowed to work metallic, cold and non-flammable material using the milling machine.

In order to avoid misuse, it is necessary to read and understand the operating instructions
before the first commissioning.

The operators must be qualified.

1.3.1 Avoiding misuse



Using suitable cutting tools.



Adapting speed settings and feed on the material and on the workpiece.



Clamp the workpiece firmly and vibration-free.

ATTTENTION!

The workpiece must always be fixed in a machine vice, jaw chucks or any other
suitable clamping tool such as e.g. clamping claws.

WARNING!

Injuries due to workpieces flying off at high speed

Clamp the workpiece in the machine vice. Make sure that the workpiece is firmly clamped in
the machine vice resp. the machine vice is firmly fixed on the machine table.



Use of cooling and lubricating agents in order to increase the durability of the tool and to
improve the surface quality.



Clamp the cutting tools and the workpieces on clean clamping surfaces.



Sufficiently lubricate the machine.



Correctly set the bearing clearance and guidance.

«
...
6
7
8
9
10
...
»

Содержание OPTIMILL MH 28V





























































Отзывы:

Нет отзывов

Похожие инструкции для OPTIMILL MH 28V

Бренд: IBM Страницы: 66

Бренд: Navitar Страницы: 6

Бренд: Magnaflux Страницы: 6

Бренд: Mafell Страницы: 46

Бренд: Keithley Страницы: 160

Бренд: Keithley Страницы: 22

Бренд: Keithley Страницы: 66

Бренд: Keithley Страницы: 58

Professional GSH65-C5

Бренд: P.I.T. Страницы: 20

Бренд: tacwise Страницы: 5

Бренд: Tool Connection Страницы: 2

vector solo 79965 solventborne RS70-AS

Бренд: Ransburg Страницы: 60

Бренд: Findeva Страницы: 3

Бренд: 3B SCIENTIFIC PHYSICS Страницы: 24

Бренд: Greenlee Страницы: 12

Бренд: Jet Страницы: 40

Бренд: Campbell Hausfeld Страницы: 15

Бренд: Chicago Electric Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды