Optimum OPTIMILL MH 28V Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 60

background image

OPTIMUM

M A S C H I N E N - G E R M A N Y



201

2

Safety

Version 1.0.1 dated 30 / 08 / 2012

Page 7

Original operating instructions

MH28V

GB

1.1.2 Further pictograms

1.2

Proper use

WARNING!

In the event of improper use, the drilling-milling machine



will endanger the staff,



will endanger the drilling-milling machine and other material property of the oper-
ator,



may affect the proper operation of the drilling-milling machine.

The drilling-milling machine is designed and manufactured to be used for milling and drilling
cold metals or other non-flammable materials that do not constitute a health hazard by using
commercial milling and drilling tools.

The drilling-milling machine must only be installed and operated in a dry and well-ventilated
place.

If the drilling-milling machine is used in any way other than described above, modified with-
out the authorisation of the company Optimum Maschinen Germany GmbH or operated with
different process data, then the drilling-milling machine is being used improperly.

We do not take any liability for damages caused by improper use.

We would like to stress that any modifications to the construction or technical or technologi-
cal modifications that have not been authorised by the company Optimum Maschinen Ger-
many GmbH will also render the guarantee null and void. It is also part of proper use that



the maximum values for the drilling-milling machine are complied with,



the operating manual is observed,



inspection and maintenance instructions are observed.



“Technical data“ on page 16

Activation forbidden!

Read the operating

manual before the

machine is first used!

Pull the mains plug!

Use protective goggles!

Use protective gloves!

Use protective boots!

Wear a safety suit!

Use ear protection!

Protect the environ-

ment!

Contact address

«
...
5
6
7
8
9
...
»

Содержание OPTIMILL MH 28V





























































Отзывы:

Нет отзывов

Похожие инструкции для OPTIMILL MH 28V

Бренд: Gearwrench Страницы: 3

Бренд: parktool Страницы: 2

Бренд: Metabo Страницы: 5

SPD1000X Series

Бренд: SIGLENT Страницы: 24

Бренд: Silverline Страницы: 2

Бренд: HIKOKI Страницы: 20

Бренд: Elenco Electronics Страницы: 8

Бренд: Huskie Tools Страницы: 16

Бренд: Laguna Tools Страницы: 17

Portable AC-to-DC Regulated Power Supply

Бренд: Radio Shack Страницы: 28

GREAT STUFF PRO 13

Бренд: Dow Страницы: 4

Бренд: Rapid Страницы: 87

Бренд: Matatakitoyo Torque Tools Страницы: 2

Бренд: MAC TOOLS Страницы: 2

Бренд: WAREMA Страницы: 4

Бренд: HB-THERM Страницы: 3

Бренд: iBell Страницы: 16

Бренд: Topeak Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды