Optimum OPTIMILL MH 28V Скачать руководство пользователя страница 6

Страница: 6 / 60

OPTIMUM

M A S C H I N E N - G E R M A N Y



Safety

Version 1.0.1 dated 30 / 08 / 2012

Page 6

Original operating instructions

MH28V

1.1

Safety warnings (warning notes)

1.1.1 Classification of hazards

We classify the safety warnings into various levels. The table below gives an overview of the
classification of symbols (pictograms) and warnings for the specific danger and its (possible)
consequences.

Pictogram

Alarm expres-

sion

Definition/Consequences

DANGER!

Imminent danger that will cause serious injury or death to per-
sons.

WARNING!

Risk: a danger that might cause serious injury or death to per-
sons.

CAUTION!

Danger or unsafe procedure that might cause injury to persons
or damage to property.

ATTENTION!

Situation that could cause damage to the drilling-milling machine
and to the product and other types of damage.

No risk of injury to persons.

INFORMATION

Application tips and other important/helpful or useful information
and notes.

No dangerous or harmful consequences for persons or objects.

In the case of specific dangers, we replace the pictogram by

general danger

with a warning
of

injuries to
hands,

hazardous elec-
trical voltage,

rotating parts.

Содержание OPTIMILL MH 28V





























































Результаты поиска

Содержание OPTIMILL MH 28V

Отзывы:

Похожие инструкции для OPTIMILL MH 28V

Бренды по названию

Популярные бренды

Optimum OPTIMILL MH 28V, Руководство по эксплуатации

Результаты поиска

Содержание OPTIMILL MH 28V

Отзывы:

Похожие инструкции для OPTIMILL MH 28V

Бренды по названию

Популярные бренды