Optimum OPTIMILL MH 28V Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 60

background image

OPTIMUM

M A S C H I N E N - G E R M A N Y



201

2

Unpacking and connecting

Version 1.0.1 dated 30 / 08 / 2012

Page 21

Original operating instructions

MH28V

GB

3.4

Installation and assembly

3.4.1 Site requirements

Organize the working space around the drilling-milling machine according to the local safety
regulations.

INFORMATION

In order to provide for good functionality and high machining accuracy as well as long dura-
bility of the machine the site should fulfill certain criteria.

Observe the following items:



The device must only be installed and operated in dry ventilated places.



Avoid places nearby machines generating chips or dust.



The site has to be vibration-free, i.e. at a distance from presses, planing machines, etc.



The substructure has to be appropriate for drilling-milling machine. Also make sure that
the load bearing capacity and the evenness of the floor are appropriate.



The substructure has to be prepared in a way that possibly used coolant cannot pene-
trate into the ground.



Protruding parts such as stops, handles, etc. need to be secured by measures provided
by the customer if necessary in order to avoid dangers for persons.



Provide sufficient space for assembly and operating staff as well as for material transport.



Also allow for accessibility for setting and maintenance works.



Make sure that the mains plug of the turning machine is freely accessible.



Provide for sufficient illumination (minimum value: 500 lux, measured at the tool tip). In
case of little intensity of illumination provide for additional illumination i.e. by a separate
workplace illuminator.

INFORMATION

The mains plug of the drilling-milling machine has to be freely accessibl

3.4.2 Load suspension point

WARNING!

Danger of crushing and overturning. Proceed with extreme caution when lifting, installing
and assembling the machine.



Secure the load suspension device around the drill-mill head. Use a lifting sling for this
purpose.



Clamp all the clamping levers at the drilling-milling machine before lifting the drilling-mill-
ing machine.



Make sure that no add-on pieces or varnished parts are damaged due to the load sus-
pension.

3.4.3 Installation



Check the horizontal orientation of the base of the drilling-milling machine with a spirit
level.



Check that the foundation has sufficient floor-load capacity and rigidity. The total weight
amounts from 205 to 220 kg.

«
...
19
20
21
22
23
...
»

Содержание OPTIMILL MH 28V





























































Отзывы:

Нет отзывов

Похожие инструкции для OPTIMILL MH 28V

Бренд: TE Connectivity Страницы: 8

Бренд: Metabo Страницы: 5

SPD1000X Series

Бренд: SIGLENT Страницы: 24

Бренд: Hilti Страницы: 4

Бренд: Alemite Страницы: 66

Бренд: Cetacea Sound Страницы: 2

Бренд: Westfalia Страницы: 23

Бренд: Zenith Страницы: 12

Бренд: IGM Страницы: 10

Бренд: Black+Decker Страницы: 32

Бренд: LEYBOLD Страницы: 3

Бренд: Performance Tool Страницы: 4

Бренд: LEVIOR Страницы: 2

Бренд: Yokota Страницы: 8

Бренд: Neilsen Страницы: 16

LIFESTAR 20-1000TUL-DC

Бренд: Vanner Страницы: 14

Бренд: Malibu Boats Страницы: 2

Бренд: Altronix Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды