Optimum OPTIMILL MH 28V Скачать руководство пользователя страница 12

Страница: 12 / 60

OPTIMUM

M A S C H I N E N - G E R M A N Y



Safety

Version 1.0.1 dated 30 / 08 / 2012

Page 12

Original operating instructions

MH28V

1.8.1 EMERGENCY-STOP button

The EMERGENCY-STOP button
switches the drilling-milling machine off.



“Switching on the drilling-milling

machine“ on page 26

Fig.1-1:

EMERGENCY-STOP button

ATTENTION!

The EMERGENCY-STOP button switches off the drilling-milling machine immediately.

Only press the EMERGENCY-STOP button in case of danger! If the button is actuated
in order to stop the drilling-milling machine generally you might damage tools or
workpieces.

After actuating the button, turn it to the right, in order to restart the machine.

1.8.2 Protective cover

The drill-mill head is fitted with a protec-
tive cover.

WARNING!

Remove the protective cover only
after the mains plug has been pulled
out of the socket.

Fig.1-2:

Protective cover

1.8.3 Separating protective equipment

Adjust the protective equipment to the correct
height before you start working.

To do so, detach the clamping screw, adjust the
required height and retighten the clamping
screw.

A switch is integrated in the fixture of the spindle
protection which monitors that the cover is
closed.

INFORMATION

You cannot start the machine if the drill chuck
protection is not closed.

Fig.1-3:

Separating protective equipment

EMERGENCY-STOP

Protective cover

Locking screw

Содержание OPTIMILL MH 28V





























































Результаты поиска

Содержание OPTIMILL MH 28V

Отзывы:

Похожие инструкции для OPTIMILL MH 28V

Бренды по названию

Популярные бренды

Optimum OPTIMILL MH 28V, Руководство по эксплуатации

Результаты поиска

Содержание OPTIMILL MH 28V

Отзывы:

Похожие инструкции для OPTIMILL MH 28V

Бренды по названию

Популярные бренды