Optimum OPTi drill RD 3 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 50

Optimum OPTi drill RD 3 Скачать руководство пользователя страница 44

OPTIMUM

M A S C H I N E N - G E R M A N Y

Appendix

Version 1.0.2 2017-04-11

Page 44

Original operating instructions

RD3

GB

8.3

Storage

ATTENTION!

Incorrect and improper storage might result in damage or destruction of electrical and
mechanical machine components.

Store packed and unpacked parts only under the intended environmental conditions.

Follow the instructions and information on the transport box.

Consult Optimum Maschinen Germany GmbH if the machine and accessories are stored for
more than three months or are stored under different environmental conditions than those spec-
ified here.

8.4

Liability claims/warranty

Besides the legal liability claims for defects of the customer towards the seller, the manufac-
turer of the product, OPTIMUM GmbH, Robert-Pfleger-Straße 26, D-96103 Hallstadt, does not
grant any further warranties unless they are listed below or were promised as part of a single
contractual provision.



Liability or warranty claims are processed at OPTIMUM GmbH's discretion either
directly or through one of its dealers.
Any defective products or components of such products will either be repaired or
replaced by components which are free from defects. Ownership of replaced products
or components is transferred to OPTIMUM Maschinen Germany GmbH.



The automatically generated original proof of purchase which shows the date of purchase,
the type of machine and the serial number, if applicable, is the precondition in order to
assert liability or warranty claims. If the original proof of purchase is not presented, we are
not able to perform any services.



Defects resulting from the following circumstances are excluded from liability and warranty
claims:
- Using the product beyond the technical options and proper use, in particular due to over-



Fragile goods
(Goods require careful handling)



Protect against moisture and humid environment

"Environmental conditions of rel. humidity“ on page



Prescribed position of the packing case
(Marking the top surface - arrows pointing up)



Maximum stacking height

Example: not stackable - do not stack a second
packing case on top of the first one.

«
...
42
43
44
45
46
...
»

Содержание OPTi drill RD 3



















































Отзывы:

Нет отзывов