Opticon MDI-4000 Series Скачать руководство пользователя страница 63

Страница: 63 / 139

MDI-4000 Series Serial Interface Manual

5.6.4

Trigger Delay

Set the Trigger Delay to start reading after a specified period of time.

Trigger Delay Commands

Command

Description

Default

[DEC

Trigger delay time (1000a+100b+10c+d [s])

0 ms

Figure 36: Trigger Delay Timing

Barcode Options

Barcode options for the scan engine let you configure the enabled code types, code specific
options, and the number of characters to read. These settings do not affect reading 1D menu
barcodes.

Note:

For best reading performance, only enable the barcodes you need.

6.1

How to Set Readable Barcodes

The next tables show the supported symbologies and their configuration commands. These
options are available for the Enable/Disable command:

•

Single: Only the specified symbology is enabled. All other symbologies are disabled.

•

Multiple: The specified symbology is enabled in addition to the symbologies that are

already enabled.

•

Disable: The specified symbology is disabled. All symbologies that are already enabled

remain enabled.

TxD
or
USB-

TRIGn

RxD
or
USB+

Scan

Trigger delay

Trigger delay time

Data

“Z”

Command

Imaging and Decoding

Содержание MDI-4000 Series












































































































































Результаты поиска

Содержание MDI-4000 Series

Отзывы:

Opticon MDI-4000 Series, Руководство по последовательному интерфейсу, Страница: 63 / 139

Результаты поиска

Содержание MDI-4000 Series

Отзывы: