Optical Systems Design OSD138 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 20

Optical Systems Design OSD138 Скачать руководство пользователя страница 12

OPTICAL SYSTEMS DESIGN

DOC ID: 10105510

OSD138 OPERATOR MANUAL

PAGE 10

2.3

OSD138 OPERATION

When using the OSD138 for the first time, check that the unit is in good condition with no visible
damage.

If a card version is used, insert it in an appropriate slot on the OSD chassis and check that the indicators
illuminate as per Table 5 on power up. If a module version (OSD138C) is used, connect the unit to an
appropriate power source and check that the indicators illuminate as per Table 5 on power up.

Plug the digital signal source. Check that the “Power” (see Figure 6) indicator is illuminated green. If it
is not illuminating, there may be a problem with the unit and it should not be used. The "Tx Data" and
"Rx Data" should not illuminate.

Setting of RS422, RS232 or RS485 data transfer is done by setting switches on the 6 Way Data Mode
Switch according to Table 6. If RS485 is used Table 7 gives the settings for turnaround times.

Connect the Data cables to 8-way mating terminal connector according to Table 3 then plug it into the
connector on the OSD138 unit.

The LED indicator "Tx Data" should illuminate amber when Data is being transmitted.

2W RS485 OPERATION WARNING:

It is essential that the external equipment’s 2w RS485 data connection to the OSD138 be the
correct polarity ie

Data +

↔

OSD138 I/O +

Data -

↔

OSD138 I/O –

or

Data +

↔

Pin 1

Data -

↔

Pin 2

If these connections are reversed it is likely that the will be no communications or just one way
communications. Such a situation may be indicated by the Tx LED indicator on one unit
permanently glowing (ie it is transmitting) and the Rx LED on the other unit permanently
glowing (ie it is receiving).

«
...
10
11
12
13
14
...
»

Содержание OSD138





















Отзывы:

Нет отзывов