Optex SC-U1 Скачать руководство пользователя страница 84

Страница: 84 / 92

When in trouble

Error details

Cause

Action

Nothing is

displayed on

the display.

A power cable is not

wired.

Check the internal wiring and be sure to wire

correctly.

The power is off.

Open the cover and turn on the power switch.

The breaker is engaged. Remove the cause of the problem and reset the

breaker.

The transmitter is out of

order.

The transmitter must be repaired. Contact the

dealer.

Displayed

characters are

hard to see.

The contrast setting is

not proper.

Refer to "Contrast setting" P.55 to adjustment.

The display is not clean. Refer to "Maintenance (Monthly)" P.89 to perform

cleaning.

The protective film has
not been removed.

Remove the protective film from the display.

The display

backlight is dark

or not lit.

The backlight setting is

configured as OFF or

Low.

Refer to "Backlight setting" P.56 to change the

setting.

The backlight timer is

too short.

Refer to "Backlight Timer" P.57 to change the

setting.

The display is not clean. Refer to "Maintenance (Monthly)" to perform

cleaning.

The display

backlight is not

lit.

The backlight timer is

too long.

Refer to "Backlight Timer" P.57 to change the

setting.

Operation

buttons do not

react.

The passcode lock has

been enabled.

When the Locking button icon (

) is displayed in

the status bar, passcode lock is enabled.

Refer to "Unlock passcode" P.18 to unlock the

passcode.

The transmitter is out of

order.

The transmitter must be repaired. Contact the

dealer.

Passcode lock

cannot be

unlocked.

The entered passcode

is incorrect.

Passcode lock is forcibly unlocked. Use the same

measures if you forgot the passcode.

Press the buttons

→

in this order within 5 seconds while no value

is entered in the passcode input display.
After forcibly resetting, reset the passcode

according to “Passcode” P.53.

Содержание SC-U1





























































































Результаты поиска

Содержание SC-U1

Отзывы:

Похожие инструкции для SC-U1

Бренды по названию

Популярные бренды

Optex SC-U1, Руководство по эксплуатации

Результаты поиска

Содержание SC-U1

Отзывы:

Похожие инструкции для SC-U1

Бренды по названию

Популярные бренды