background image

 

CIA-675-001 Rev 1.1 

3 | 

P a g e

 

 

  

Direct: (602) 773-1700 

Main: (800) 481-7459 

 

2101 W Peoria Ave, Suite 100 

Phoenix, AZ 85029

 

[email protected]

www.opentechalliance.com

 

Table of Figures 

Figure 1 - Gateway Components…………………………………………………………………………………………………...5

 

Figure 2 - Gateway Physical Dimensions ................................................................................................................ 6 

Figure 3 - Gateway Baseline (Minimum) Wiring .................................................................................................. 6 

Figure 4 - Gateway Wiring Connections ................................................................................................................. 7 

Figure 5 - Relay Ratings ................................................................................................................................................ 9 

Figure 6 - Tamper Alarm Reset .................................................................................................................................. 9 

Figure 7- Fuses and Indicators ................................................................................................................................ 11 

Figure 8 - Fuse to System Size Relationship Diagram .................................................................................... 12 

Содержание INSOMNIAC CIA G-600














Отзывы: