OpenEye OE-C1012D2 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 44

OpenEye OE-C1012D2 Скачать руководство пользователя страница 24

24

Snapshot

The Snapshot tab is used to configure the settings for timed or continual snapshots.

To configure Snapshots:

1.

Use the dropdowns to select the desired

Resolution

,

Snapshot Interval

, and the

Number of

Snapshots

.

2.

If you desire Scheduled Snapshots, select

Schedule

Snapshot Mode, and designate snapshot

times.

3.

Save

Parameter

Description

Snapshot Interval

Interval between two snapshots. For example, with Snapshot Interval set to 1 and

Number of Snapshot set to 2, the camera will take 2 snapshots (take one first and

then take another after 1 second).

Number to Snapshot

Currently 1, 2, and 3 snapshots are allowed.

Snapshot Mode

Schedule

: You need to set a snapshot time, e.g., 19:12:00, which means the camera

takes a snapshot at 19:12:00.

Repeat

: Allows you to set an interval (unit: sec). For example, according to the

settings shown in the figure above, 60 seconds must elapse before the camera

takes another two snapshots.

«
...
22
23
24
25
26
...
»

Содержание OE-C1012D2













































Отзывы:

Нет отзывов