Grow Wall3C
A. Assembly
A1. Remove all the parts from box and check all the accessories
Thank you for purchasing OPCOM Farm Grow Wall 3C, the indoor hydroponics growing system. lt is designed for easy to use and
efficient growth by one-touch AUTO mode.lt holds up to 144 plants capacity. Please read the quick guide carefully before setting it up.
For detailed user guide video, please visit Grow Wall 3C page at http://www.opcomfarm.com
Seedling Tray x2pcs
(665*175*65mm)
Grow Kits
Assembly
Grow Sponge 60pk x9pcs
(OASP001)
EC Meter
x1pc
pH test
paper x1pc
Accessories
LED Growth Light x4pcs
Control Box x 1pc
Base Stand
x2pcs
Hose x 1pc
Warranty Card Manual
Maple plank
x2pcs
Power socket
cable x1pc
Tube x4pcs
Backup Pump x 1pc
AC/DC adapder x 1pc
power cable x1pc
Planting Tray(36 holes) x4pcs
Ribbon x10pcs
Soda (pH+)
50ml x1
Salt #1 (Nutrition)
250ml x2
Lemon(pH-)
50ml x2
Cleaning
ponge x1pc
Water
Spray x1pc
Remote
Controller x 1pc
Filter
Sponge x5pcs
B Scoop for Adjust
of Nutritio (5g)
A2. Assemble GrowWall3
Lift the wooden lid on top the fan's crossbeam. Plug the fan's power into
the fan socket, the first slot of the power socket cable, then close the lid.
Assemble and secure the cross beam of the top fan and R3 colume with
screws.
1
2
Assemble the R3 column and the R2 column.
3
Hang the L4 planting groove and L3 planting groove on the columns
through the holes on the side planting grooves.Once hanged, set and
secure the clip onto the mechanism
4
Assemble the R2 column and the R1 column.
5
Assemble the L2 planting groove and the L1 planting groove on
the column.(see step.4)
6
Stick the maple planks on the exterior of the assembled columns.
8
Fix the power socket cable into the line groove in the column.
7
Dissembling the top and the bottom of the tube gives an aluminum
and a plastic tube.
Face the teeth of the aluminum tube downwards, then, from the interior
of the planting groove, work the tube through the holes on the bottom.
cover the tip of the aluminum tube in the planting groove with a filter
sponge.
11
9.Set the LED grow light on the rocker arm on each layer of
columns. To set up, unscrew the thumb screw on the side of the
LED grow lights, remove the two circular spacers.
Place one spacer between the tip of the rocker arm and the side of the
LED grow light. Place another spacer between the thumb screw and the
tip of the rocker arm.
Once done, align the holes between each part and secure them with a
thumb screw.
9
Plug the power cord of the LED growth light into the LED socket of the
power socket cable on the column.
Organize the cables of the LED grow light and fix them in the line
groove on the rocker arm.
10
Set the water tank under the L1 planting groove.
Place the planting tray into the planting groove. Make sure
to correspond each water inlet of the planting tray to the
holes on the bottom of the planting groove.
12
Set the plastic tube in the water inlet of the planting tray.
Connect the tip of the aluminum tube at the bottom of the
planting groove by rotating.
13
Fill the water tank with 8gallons of water.
14
Plug the AC/DC adapter into a the power socket cable, then
connect the AC/DC adapter with the power cable to power
up the machine.
15
Draining Water Tank:
1. Open the water control box on the left side of the water tank by pulling
up the side planks. Take out the water drain pipe form the storing disk.
2.Prepare a water bucket with a capacity of around 40 L. Place the outlet of
thepipe un the bucket.
Turn On the pump and switch the water drain valve to Out to start draining.
3.Once finished draining, set everything back to default. (turn off the pump
and stop the water drain valve.)
16
5. LED light planting mode Control
Chart I: Control Box Mode
Most plants can be grown using the AUTO mode.
Fan follow LEDon / off.
Restore factory settings after power failure.
Set up the Wake-up(automatically turns on everyday) and Sleeping(automatically turns off everyday) modes through lighting time setting.
A. When Power On, press hold POWER button until 2 beep sound (About 5 second) to reset power on timeline.
B. When Power Off, press hold POWER button until 2 beep sound (About 5 second) to reset power off timeline.
1.Select the mode of the LED grow light (you may switch between modes through the button on the
left side of the LED lamp holder).
2.The light comes with four modes: G(in green), S(in orange), L(in orange), and Off(colorless)(see
figure 1).
3.Please note that the remote control could only adjust the duration of lighting (On/ Hi /Low /Off),
as shown in chart 1. To switch between the mode of the LED grow light, please access the buttons on the light tubes manually.
4.Height of the LED grow light: Adjust the height and the angle of lighting manually through the rocker arm(see figure 2).
5.This hydroponics system comes with fans that improve the air circulation and accelerate the cooling of the LED tubes, which increases
the ventilation and avoids plants from overheating. Please make sure to keep a 5-10 cm distance between the light tube and the
plants to further prevent plants from overheating. To boost the light intensity in a power-saving way, direct the light at both the plant
and the wall simultaneously, which could add 30% more lighting to the plants.
Please read and follow every steps to avoid any malfunction.
B. Seedling
Chart II: Plant Stage
(Fig4)
(Fig3)
This side up!
(Fig2
）
(Fig1
）
1. Add water to the seedling tray, up to the water (red) level.(Fig1)
2. First time sprout: just open the seedling box and add water. Then go to step 4. (Fig 1)
3. Second time sprout: Open Grow Sponge package,put each sponge piece into water of seedling tray
(make sure the front side with the seed label is side up), press the sponges into water 5 seconds and
ensure the sponges absorb water completely. Put seed moisturizing cover on the sponges.(Fig2)
4. Place the seedling tray with cover in the shade.(Fig3)
5. Suggest using Watering Spray water to sponges and keep them wet everyday.
6. During 0 ~ 7 days, find the sprouted ones in the tray; pick them out, and move them into product (make
sure the sponges lineup with the black dot on the partition)(Fig4) and to next stage: B2. Young Plant Stage.
7. Discard unsprouted sponges after regular germination time.
8. In each sponge, keep strong plants and cut the other weak plants.
* Different plant may have different germination time, please check before plant.
B1. Germination Stage
B2.Young Plant Stage
1. Add 10.5 gallons water to the water tank.
2. During Young Plant Stage, turn on LED and Pump. Please refer to the ChartII.
3. Add Salt #1 (Nutrition) into the water tank and ensure EC value between(=1.0-2.0mS/cm)
Status
Salt #1 (Nutrition)
0.0-0.5
Add 2g
0.5-1.0
Add 1g
1.0-1.5
Standard range
over 2.0
Add water
Grow Kits:
B Scoop for Adjust of Nutritio (5g)
Basil, Lemon Balm
Germination Stage
Planting Time
Day 0~7
LED Mode
-
Pump Mode
-
Notes
* For your expected plant amount, you can refer to the sprout rate of 1st planting cycle.
* If you need more planting information, please vist to www.opcomfarm.com and read “Plant Q&A”.
Nutrition
-
T
( )
68 - 77
RH
80%
EC
0.5-1.0
pH
5.5-6.5
Young Plant Stage
Day 3~14
ON
ON
59 - 86
45%-70% 1.0-2.0
5.5-6.5
Growing Stage
After Day 14
Auto
Auto
59 - 86
45%-70% 1.0-2.0
5.5-6.5
Be sure each sponge is fully wet in
seedling tray.
* Please keep the seeds in refrigerator if you don’t use it, recommended temperture is 41
-
50.
Need
Need
Fan socket
Layer 4
LED
sockets
Layer 3
LED
sockets
Layer 2
LED
sockets
Layer 1
LED
sockets
Control
box
socket
Motor
socket
15
15
L1 planting groove
Water tank
L2 planting groove
L3 planting groove
L4 planting groove
fan beam
R1
column
R2
column
R3
column
Screw pack
x1pc
planting basket
(25mm) x150pcs
Time
On (Follow last mode before turn off)
Off
12Hr/day ON mode of LED and 30mins/ 2Hr ON mode of Pump
Follow LED and Pump manual mode seting
55mins/ 1Hr
25mins/ 30mins
5mins/ 30mins
always Off
Status
Operation
Fuction
ON
High
Low
OFF
One Press
One Press
One Press
One Press
Pump
On
Off
On
One Press
One Press
One Press
Power
Auto
Light
Sound
BB
BB
Off
One Press
B 1sec
B 1sec
BB
BBB
BBBB
B 1sec
B 1sec
always On
18Hr/day
9Hr/day
always Off
ON
High
Low
OFF
One Press
One Press
One Press
One Press
LED
BB
BBB
BBBB
ON
HI
LOW
OFF
ON
HI
LOW
OFF
ON
HI
LOW
OFF
ON
HI
LOW
OFF
ON
HI
LOW
OFF
ON
HI
LOW
OFF
ON
HI
LOW
OFF
ON
HI
LOW
OFF
1
3
4
4
4
9
9
8
12
11
10
10
10
10
2
11
12
13
7
Remote Control
Smart Control Box
11 gallons
（
40L
）
Water Control Box
Water Drain pipe
Water Cycling pipe
Pump
Water Cycling Valve
Water Drain Valve
16
figure 1
figure 2
L mode
G mode
S mode
Off
Adjust the height of lighting
Adjust the angle of lighting
Alkaline
Neutral
Acidic
