INTRODUCTION
The One For All 4 Device Universal
Remote Control is designed to operate
three (or four) home entertainment
devices, depending on the model pur-
chased (see
Key Charts, Mode Keys
on
the right).
The remote control requires four fresh
AAA alkaline batteries (not included) and
easy programming to control your devices.
For best results, please read and perform
all instructions listed here.Also, keep
these instructions for future reference.
FEATURES AND FUNCTIONS
Use the
Key Charts
to learn how to use the
universal functions of the One For All 4
Device Universal Remote Control.
Key Charts
Use
SET
for all
programming
sequences.
The
LED
(red light)
blinks to show that
the remote control is
working and is
sending signals.
Press
POWER
once to
turn on or off the
selected device.
Mode Keys for 4 Device:
Press
VCR
,
DVD
,
TV
, or
CBL/SAT
once to select
a home entertainment
device to control.
Use the keypad (
0
~
9
)
to directly select
channels (for example,
09 or 31).
Press
MUTE
once to
turn sound off
or on.
Press
PREV CH
once to
recall the last-viewed
channel and to page
back one screen on the
main menu.
Press
ENTER
once
after entering channel
numbers on some TV
models.
Use
MENU
to choose
options from your
selected device’s
menu.
Use
VOL+
(or
VOL-
)
to raise (or lower) the
sound volume.
Use
CH+
(or
CH -
) to
select the next higher
(or lower) channel.
Press
SLEEP
to activate
your device’s sleep
timer (not available
for all devices).
Use the transport keys
to control your VCR,
CD or DVD player, or
VOD. To record a
program, press the
record key (
REC
)
twice.
use TV/VID to switch
the TV’s input to view
TV or video program.
INSTALLING BATTERIES
1. On the remote control’s back, push the
tab and lift off the battery cover.
2. Obtain four (4) fully-charged AAA
alkaline batteries. Match the + and –
marks on the batteries to the + and
– marks in the battery case, then
insert the new batteries.
3. Press the battery cover back into
place. The tab should click when the
cover is locked.
4. Test the unit by pressing
POWER
and any mode key (e.g.,
TV
). If the
batteries are inserted correctly, the
LED will blink once.
NOTE: When batteries need replacement,
the remote control will stop operating.
Remove the old batteries and insert new
ones within 30 minutes to ensure all of
your programming information is restored.
PROGRAMMING
DEVICE CONTROL
The One For All 4 Device remote control
is preprogrammed at the factory to
operate an RCA TV and VCR, a Motorola
(GI) cable box, and a Toshiba DVD play-
er. To control devices other than the
default brands, perform the following
steps; otherwise skip this section:
NOTE: For TV/VCR Combo control, see the
next section.
1. Turn on a device (e.g.,VCR) and, if
applicable, insert media, (e.g.,
cassette or disc).
NOTE: Please read steps 2-4 completely
before proceeding. Highlight or write down
the codes and device you wish to program
before moving on to step 2.
2. On the remote control, press a device
key once (i.e.,
VCR
,
DVD
,
TV
, or
CBL/SAT
). Press and hold
SET
until
the LED blinks twice, then release
SET
.
3. Use the
Manufacturer’s Codes
to
locate the type of device and brand
name and then enter the first four-
digit code for your component. If
performed correctly, the LED will
blink twice.
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
the same code again.
4. Aim the remote control at the device
and press
POWER
once. The device
should turn off. If it does not respond,
repeat steps 2-3, trying each code for
your brand until you find one that
works. If it still does not work, try
Searching For Your Code
.
NOTE: If the device does not have a
POWER
key, press the (
PLAY
) key.
5. Repeat steps 1 through 4 for each
device you want to control.
PROGRAMMING
TV/VCR COMBO CONTROL
Perform the following instructions to
control a TV/VCR Combo:
1. Turn on the TV/VCR Combo and
insert a video cassette.
NOTE: Please read steps 2-4 completely
before proceeding. Highlight or write down
the codes and device you wish to program
before moving on to step 2.
2. On the remote control, press
VCR
.
Press and hold
SET
until the LED
blinks twice, then release
SET
.
3. Use the
Setup Codes For TV/VCR
Combos
(on the back side) to locate
the brand name and then enter the
first four-digit code for your device.
If performed correctly, the LED will
blink twice.
NOTE: If the LED did not blink twice, then
repeat steps 2 through 3 and try entering
the same code again.
4. Aim the remote control at the device
and press
POWER
once. It should turn
off. If the device does not respond,
repeat steps 2-3, trying each code for
your brand until you find one that
works. If it still does not work, try
Searching For Your Code
.
NOTE: If the device does not have a
POWER
key, press the (
PLAY
) key.
5. If you’ve located a TV/VCR setup
code that works your TV/VCR
Combo and a separate TV code is
also listed, you’ll need to program
this code into the remote control to
access volume control .
SEARCHING FOR YOUR CODE
If your device does not respond to the
remote control after trying all codes
listed for your brand, or if your brand is
not listed at all, try searching for your
code. For example, to search for a code
for your TV:
1. On the remote control, press
TV
once.
2. Press and hold
SET
until the LED
blinks twice, then release
SET
.
3. Enter
9
-
9
-
1
. The LED will
blink twice.
4. Aim the remote control at the the
TV and slowly alternate between
pressing
POWER
and
TV
. Stop when
the TV turns off.
NOTE: In the search mode, the remote
control will send IR codes from its library
to the selected device, starting with the
most popular code first.
5. To lock in the code, press and hold
SET
until the LED blinks twice, then
release
SET
.
6. To search for the codes of your other
devices, repeat steps 1 through 5, but
substitute the appropriate device key
for the device you are searching for.
CHECKING THE CODES
If you have set up the remote control
using the
Searching For Your Code
procedure, you may need to find out
which four-digit code is operating your
equipment:
For example, to find out which code is
operating your TV:
1. On the remote control, press
TV
once.
2. Press and hold
SET
until the LED
blinks twice, then release
SET
.
3. Enter
9
-
9
-
0
. The LED will
blink twice.
4. To view the code for the first digit,
press
1
once.Wait 3 seconds, count
the LED blinks (e.g., 3 blinks = 3)
and write down the number.
NOTE: If a code digit is “0”, the LED will
not blink.
5. Repeat step 4 three more times for
remaining digits. Use
2
for the
second digit,
3
for the third digit,
and
4
for the fourth digit.
6. To check for codes of other devices,
repeat steps 1 through 5, but substi-
tute the appropriate device key for
each device you are checking.
As before, write down each four-
digit code.
RE-ASSIGNING DEVICE KEYS
The One For All 4 Device can be set to
control a second TV,VCR, or DVD player.
For example, to control two TVs, a VCR,
and a cable box, you will need to re-
assign the unused
DVD
key to operate
the second TV as follows:
1. On the remote control, press and
hold
SET
until the LED blinks twice,
then release
SET
.
2. Enter
9
-
9
-
2
. The LED will
blink twice.
3. Press
TV
once, then press
DVD
once.
4. The
DVD
key is now ready to be
programmed for your second TV.
See
Programming Device Control
.
To re-assign other device keys, repeat
steps 1 through 4 by substituting the key
sequence from the below chart for the
most popular components:
To Re-Assign Key
Sequence
Perform
VCR
as 2nd TV key:
SET
-
9
-
9
-
2
-
TV
-
VCR
VCR
as 2nd CBL key:
SET
-
9
-
9
-
2
-
CBL/SAT
-
VCR
VCR
as 2nd SAT key:
SET
-
9
-
9
-
2
-
CBL/SAT
-
VCR
VCR
as 2nd DVD key:
SET
-
9
-
9
-
2
-
DVD
-
VCR
VCR
back to
VCR
:
SET
-
9
-
9
-
2
-
VCR
-
VCR
DVD
as 2nd TV key:
SET
-
9
-
9
-
2
-
TV
-
DVD
DVD
as 2nd CBL key:
SET
-
9
-
9
-
2
-
CBL/SAT
-
DVD
DVD
as 2nd SAT key:
SET
-
9
-
9
-
2
-
CBL/SAT
-
DVD
DVD
as 2nd VCR key:
SET
-
9
-
9
-
2
-
VCR
-
DVD
DVD
back to
DVD
:
SET
-
9
-
9
-
2
-
DVD
-
DVD
When a re-assignment is done, the LED
will blink twice to confirm your choice.
At that time, you will need to program
the remote control for the new device
(see
Programming Device Control
).
CHANGING VOLUME LOCK
The One For All 4 Device is set to
control the volume of your TV in the TV,
VCR, CBL/SAT, and DVD modes. If you
want the volume to be controlled by a
mode other than TV (e.g., CBL/SAT),
change the Volume Lock as follows:
To Change Volume Lock To
Another Mode:
1. On the remote control, press and
hold
SET
until the LED blinks twice,
then release
SET
.
2. Enter
9
-
9
-
3
and then press any
mode key once (except
TV
). The LED
will blink twice.
3. Now, whenever you press
VOL+
,
VOL–
, or
MUTE
, volume will be
controlled by your mode choice.
Unlocking Volume Control:
NOTE: Perform these instructions when you
want independent volume control for each
programmed device (e.g., TV volume control
in TV mode, CBL/SAT volume control in
CBL/SAT mode, etc.)
1. On the remote control, press and
hold
SET
until the LED blinks twice,
then release
SET
.
2. Enter
9
-
9
-
3
and then press
VOL+
.
The LED will blink four times.
3. Volume will again be controlled
according to its default states.
TROUBLESHOOTING
For assistance, please contact us in any
of the following ways:
• Consumer Help Line: (330) 405-8612
• Internet: http://www.oneforall.com
PROBLEM:
LED does not blink when
you press a key.
SOLUTION: Replace batteries with
four new AAA alkaline
batteries.
PROBLEM:
LED blinks when you
press a key, but home
entertainment component
does not respond.
SOLUTION: Make sure the remote
control is aimed at your
home entertainment
device and is not farther
than 15 feet away.
PROBLEM:
The unit does not control
home entertainment
devices or commands are
not working properly.
SOLUTION: Try all listed codes for the
component brands being
set up. Make sure they
can be operated with an
infrared remote control.
PROBLEM:
TV/VCR combo does not
respond properly.
SOLUTION: Use the VCR codes for
your brand. Some combo
units may require both a
TV code and a VCR code
for full operation.
PROBLEM:
Changing channels does
not work properly.
SOLUTION: If original remote control
required pressing ENTER
to change channels, press
ENTER
on the remote
control after entering the
channel number.
PROBLEM:
Tried “Search Method”
and still could not find a
working code.
SOLUTION: Clear the device key as
follows: Press and hold
SET
until the LED
blinks twice, then release.
Next enter
9
-
9
-
2
. Then
press the device key to be
cleared twice. Now repeat
the “Search Method.”
PROBLEM:
CH
▲
and
CH
▼
do not
work for your RCA TV.
SOLUTION: Due to RCA design (1983-
1987), only the original
remote control will oper-
ate these functions.
PROBLEM:
Remote control does not
turn on Sony or Sharp
TV/VCR Combo.
SOLUTION: For power on, these prod-
ucts require programming
TV codes. For Sony, use
TV code 0000 and VCR
code 0032. For Sharp, use
TV code 0093 and VCR
code 0048.
MANUFACTURER’S CODES
Setup Codes for TVs:
AOC
0030, 0019, 0052
Admiral
0093, 0463
Aiko
0092
Akai
0030
Alaron
0179
Ambassador
0177
America Action
0180
Ampro
0751
Anam 0180
Audiovox
0451, 0180, 0092, 0623
Baysonic
0180
Belcor
0019
Bell & Howell
0154
Bradford
0180
Brockwood
0019
Broksonic
0236, 0463
CXC
0180
Candle
0030, 0056
Carnivale
0030
Carver
0054
Celebrity
0000
Cineral
0451, 0092
Citizen
0060, 0030, 0056, 0039, 0092
Concerto
0056
Contec 0180
Craig
0180
Crosley
0054
Crown
0180, 0039
Curtis Mathes
0047, 0054, 0154, 0051, 0451, 0093,
0060,
0030, 0145, 0056, 0039, 0166, 0466,
1147,
1347
Daewoo
0451, 0019, 0039, 0092, 0623, 0624
Daytron
0019
Denon
0145
Dumont 0017, 0019
Dwin
0720, 0774
Electroband
0000
Emerson
0154, 0236, 0463, 0180, 0178, 0019,
0179,
0039, 0177, 0623, 0624
Envision
0030
Fisher
0154
Fujitsu
0179, 0683
Funai 0180, 0179, 0171
Futuretech
0180
GE
0047, 0051, 0451, 0093, 0178, 0135,
1147,
1347
Gibralter
0017, 0030, 0019
GoldStar
0030, 0178, 0019, 0056
Gradiente 0053, 0056
Grunpy
0180, 0179
Hallmark
0178
Harley
Davidson
0179
Harman
/Kardon
0054
Harvard
0180
Hitachi
0145, 0056, 0151
Infinity
0054
Inteq
0017
JBL
0054
JCB
0000
JVC
0053
KEC
0180
KTV
0180, 0030, 0039
Kaypani
0052
Kenwood
0030, 0019
LG 0056
LXI
0047, 0054, 0154, 0156, 0178
Luxman
0056
MGA
0150, 0030, 0178, 0019
MTC
0060, 0030, 0019, 0056
Magnavox
0054, 0030, 0179, 1254
Marantz
0054, 0030
Matsushita
0250
Megatron
0178, 0145
Memorex
0154, 0250, 0463, 0150, 0178, 0056
Midland
0047, 0017, 0051, 0039, 0135
Mitsubishi
0093, 0150, 0178, 0019
Motorola
0093
Multitech
0180
NAD
0156, 0178, 0166
NEC 0030, 0019, 0056
NTC 0092
Nikko 0030, 0178, 0092
CBL/SAT
VCR
DVD
TV
CBL/SAT
VCR
DVD
TV
SET
SLEEP
PREV
CH
ENTER
FF
PLAY
REW
PAUSE
STOP
TV/VID
CH +
CH -
MUTE
VOL
-
VOL
+
REC
MENU
EXIT
POWER
4 DEVICE
UNIVERSAL REMOTE CONTROL
USER’S GUIDE
