ON Semiconductor MT9P017, Руководство пользователя

Страница: 4 / 5

MT9P017LACSTCH − GEVB
www.onsemi.com
4
Table 1. JUMPERS AND HEADERS (continued)
Jumper/Header No. Description Pins Jumper/Header Name
P6 +2V8_VAA
1 − 2 (Default) Connects to on-board +2V8_VAA power supply
2 − 3 External power supply connection
P7 +VCM Open (Default) For connection to external VCM
P8 +1V8_REG_IN 1 − 2 (Default) Connects to on-board +1V8_REG_IN power supply
2 − 3 External power supply connection
P9 +1V2_VDD 2 − 3 (Default) Connects to on-board +1V2_VDD power supply
1 − 2 External power supply connection
P10 +1V2_VDDPLL 2 − 3 (Default) Connects to on-board +1V2_VDDPLL power supply
1 − 2 External power supply connection
P11 +VPP Open (Default) For OTPM programming
P12 MCLK_IN 2 − 3 (Default) Connects to on-board oscillator
1 − 2 Connects to XMCLK (i.e. clock signal from Demo 2 baseboard)
P14 +2V8_VAAPIX 1 − 2 (Default) Connects to on-board +2V8_VAAPIX power supply
2 − 3 External power supply connection
P15 +VDDIO 1 − 2 (Default) Connects to on-board +VDDIO power supply
P17 S_XSHTDN 1 − 2 (Default) Connects SHTWN_N to sensor shutdown
3 − 4 Connects RESET_N to sensor shutdown pin
5 − 6 Connects GND to sensor reset pin
P18 S_RST_N 1 − 2 (Default) Connects RST_N to sensor reset pin
3 − 4 Connects SHTDWN_N to sensor reset pin
5 − 6 Connects GND to sensor reset pin
SW2 RESET N/A When pushed, 240 ms reset signal will be sent to AR0542
SW3 EEPROM Addr. Sel EEPROM Addr. Sel EEPROM Addr. Sel A0 on, A1 on,
A2 off, WP on
(Default)
EEPROM Address set to 0xA8
A0 off, A1 off,
A2 off, WP on
EEPROM Address set to 0xAC
A0 on, A1 off,
A2 on, WP on
EEPROM Address set to 0xA4
A0 on, A1 on,
A2 on, WP on
EEPROM Address set to 0xA0
Interfacing to ON Semiconductor Demo 2X Baseboard
The ON Semiconductor Demo 2X baseboard has
a similar 26-pin which mates with P13 of the headboard.
The four mounting holes secure the baseboard and the
headboard with spacers and screws.
Shorted Jumpers for Power Measurement
Different supplies to the evaluation board are provided by
trace shorted jumper, for any voltage and power
measurements. To conduct current for current measurement
on a given power rail, cut the trace between the two pins of
their respective JP, and insert an ammeter prior to powering
up the system. The figure below shows where the trace to cut
is located.
Table 2. SHORTED JUMPERS FOR POWER
MEASUREMENTS
Jumper Voltage (V)
P16 (+5V0) 5.0
Figure 8. Top and Bottom View of Shorted Jumper. The Bottom
View Shows the Trace Location to Cut for Current Measurement
Cut here