manualshive.com logo in svg

Omron ZX-CAL, Инструкции по эксплуатации, Страница: 55 / 187

Поделиться
Скачать
Omron ZX-CAL Скачать руководство пользователя страница 55

Hardware Functions

Section 3-2

35

The following values are output according to the setting for non-measure-
ment.

Maximum output voltage: Approximately 5.5 V

Maximum output current: Approximately 23 mA

3-2-2

Outputs

Judgement Outputs

There are three judgement outputs: HIGH, PASS, and LOW.

The following table and illustration show the timing of each output.

Threshold Values

The threshold values form the boundaries between the HIGH, PASS,
and LOW outputs for the measured value.

There are two threshold values: The HIGH threshold and the LOW
threshold. The threshold values contain hysteresis.

Hysteresis

The hysteresis (hysteresis width) is the difference between the operating
and releasing values. If the hysteresis is too small, chattering may occur.
If it is too large, releasing may be difficult.

Output

Setting for non-measurement

CLAMP

KEEP

Judgement outputs

All OFF

The values immediately 

before the non-measure-

ment status are kept.

Linear output

Maximum output 

value is held.

Main display

“- - - - -“

Sub-display

The averaging operation is cleared for the reset input. The judge-
ment output response thus may be slower than normal immediately
after releasing the reset input.

POINT

Measured value

Judgement outputs

Larger than or equal to HIGH threshold

PASS 

→

 HIGH

Smaller than or equal to HIGH threshold  

−

 Hysteresis

HIGH 

→

 PASS

Smaller than or equal to LOW threshold

PASS 

→

 LOW

Larger than or equal to LOW threshold 

−

 Hysteresis

LOW 

→

 PASS

Timing of Changes in Judgement Outputs

Z157-E1-01C.book  Page 35  Thursday, August 31, 2006  5:13 PM

Содержание ZX-CAL




























































































































































































Отзывы:

Нет отзывов