manualshive.com logo in svg

Omron ZX-CAL, Инструкции по эксплуатации, Страница: 164 / 187

Поделиться
Скачать
Omron ZX-CAL Скачать руководство пользователя страница 164

Setting Problems

Section 5-2

144

5-2

Setting Problems

5-2-1

Unable to Set Scaling

Scaling cannot be set in the following cases.

• When scaling is performed outside the measurable range when a

Reflective Sensor Head is used.

• When the distance (or width) of two-point scaling is less than 10% of full

scale (FS).

• When the numeric value for scaling input is extremely small or large.

5-2-2

Unable to Set Monitor Focus

The monitor focus cannot be set when specified distances (or widths)
between two points is less than 10% of full scale (FS).

Set the monitor focus after performing scaling.

It is recommended that the linear output value for display value be deter-
mined using the scaling after setting the display value for actual distances
(or widths).

5-2-3

Unable to Set Threshold Values

Always set threshold values to satisfy the following formula:

HIGH threshold value > LOW threshold value

In addition, the threshold values cannot be set if the PASS judgement can-
not be made because the hysteresis (Hys) is too large and the following
equation is true:

(HIGH threshold value 

−

 LOW threshold value) < Hys

5-2-4

Unable to Set Hysteresis

The hysteresis cannot be set if the PASS judgement cannot be made
because the hysteresis (Hys) is too large and the following equation is
true:

(HIGH threshold value 

−

 LOW threshold value) < Hys

Decrease the setting of the hysteresis to eliminate the above condition.

Z157-E1-01C.book  Page 144  Thursday, August 31, 2006  5:13 PM

Содержание ZX-CAL




























































































































































































Отзывы:

Нет отзывов