Omron ZX-CAL Скачать руководство пользователя

Страница: 156 / 187

FUN (Function) Mode

Section 4-5

136

4-5-10 Setting the Monitor Focus

The monitor focus setting procedure is shown in the following figure:

Monitor focus

Differentiation function

Go to the

next mode

Voltage

output
Current

output

First point

distance value

First point

output value

Numeric value setting procedure is the same as

that of other FUN mode settings except for the
value shift that requires setting both output and

distance values as shown on the right:

Press the ENT Key to
migrate to the second
point monitor focus
setting.

Numeric value setting procedure is the

same as that of the first point.

Fail

Perform the monitor focus operation.

Second point

distance value

Second point

output value

Voltage output
selected using the
ENT Key

Intensity function

Start the first

point focus value

setting using the

UP, DOWN,

LEFT and RIGHT

Keys

Current output
selected using

the ENT Key

Start the second

point focus value

setting by using

the UP, DOWN,

LEFT and RIGHT

Keys.

Press the ENT Key
to complete the
monitor focus
setting.

Migrate to the intensity function

selection mode.

Circled characters are
the (flashing) digits to
be set.

Z157-E1-01C.book Page 136 Thursday, August 31, 2006 5:13 PM

Содержание ZX-CAL




























































































































































































Результаты поиска

Содержание ZX-CAL

Отзывы:

Похожие инструкции для ZX-CAL

Бренды по названию

Популярные бренды

Omron ZX-CAL, Инструкции по эксплуатации

Результаты поиска

Содержание ZX-CAL

Отзывы:

Похожие инструкции для ZX-CAL

Бренды по названию

Популярные бренды