manualshive.com logo in svg

Omron ZX-CAL, Инструкции по эксплуатации, Страница: 135 / 187

Поделиться
Скачать
Omron ZX-CAL Скачать руководство пользователя страница 135

RUN Mode

Section 4-3

115

4-3-3

Setting the Reference Incident Level

This setting is only for Through-beam Sensor Heads.

The reference incident level can be set and stored using the DOWN Key.
The reference incident level set here will be the full scale (FS) value for all
measured values. 

Procedure

Set the mode switch to RUN.

Press the ENT Key for 3 seconds or
longer without executing the zero reset.

RUN     T     FUN 

The full scale (FS) value for when none
of the beam is intercepted will be dis-
played on the main display.

The linear output will be the value set
for when none of the beam is inter-
cepted for a two-point setting for the
monitor focus.

Note: The reference incident level is
stored in the memory. When the power
is turned ON the next time, the set ref-
erence incident level will be read.

Press the DOWN Key.

Z157-E1-01C.book  Page 115  Thursday, August 31, 2006  5:13 PM

Содержание ZX-CAL




























































































































































































Отзывы:

Нет отзывов