Omron ZW-7000 Series Скачать руководство пользователя страница 41

Страница: 41 / 336

Basic Operations for Displaying Measurement Results

ZW-8000/7000/5000
User's Manual

Ba
si

c con

figuratio

• Be sure to use a Sensor Head and Calibration ROM with the same serial number.

• A pair with different serial numbers cannot operate normally.

• Make sure to initialize the Sensor Controller when connecting a different type Sensor Head from that which was

connected the previous time the Sensor Controller was launched.

For the initialization method, see below.

Initializing Settings p.187

Initializing Settings p.271

Remove the Fiber cable

For ZW-8000/7000 Series

If you have the bush section of Fiber cable, that part may be out of place. Make sure to have the fiber
connector section.

When you remove the fiber cable, make sure to have the black part of the connector which indi-

cated.

Have the fiber connector (black part) illustrated under figure, and then pull out the direction of the arrow.

ZW-

000

erie

ZW-7000

erie

Important

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды