Omron ZW-7000 Series Скачать руководство пользователя страница 334

Страница: 334 / 336

Revision History

332

ZW-8000/7000/5000

User's Manual

Revision History

A manual revision code appears as a suffix to the catalog number at the bottom of the front and back covers of

this manual.

Revision code

Date

Revision Contents

April 2016

First edition.

July 2016

Add the PDO synchronization mode and correct error sentences.

April 2017

Compatible with ZW-5000 series and correct error descriptions.

May 2017

Correct error descriptions.

May 2018

Compatible with ZW-8000 series and correct error descriptions.

June 2019

Change the text of Notice for Korea Radio Law.

November 2019

Compatible with Risk Group change of LED safety, and correct error descriptions.

March 2020

Correction of External Dimensions.

September 2022

Add description in Safety Precautions

Cat. No. Z362-E1-09

Revision code

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды