manualshive.com logo in svg

Omron ZW-7000 Series, Руководство пользователя

Поделиться
Скачать
Omron ZW-7000 Series Скачать руководство пользователя страница 272

Setting the System

270

ZW-8000/7000/5000 

User's Manual

Calibrating Sensor Head

Calibrating Sensor Head p.77

Operating procedure

When Sensor Head calibration fails

If the Sensor Head is calibrated in an inappropriate environment, an error is displayed on the main display. In such a 
case, return to the previous screen using 

 key. Then refer to the p.48, recheck your environment, and try again. 

If an error results even if Sensor Head calibration is done under the correct conditions, it is possible that some 
contaminants may have adhered to the Sensor Head part, or the fiber connector of the Sensor Controller. Clean the 
fiber cable or fiber connector referring to p.70.

Steps

Key operation

Display

Description

1

Press and hold the 

 key for two seconds or more to enter the FUNC 

mode.
Press the 

 key after [SWITCH] and [OK/CAN] are displayed.

To save the setting, refer to "7-3 Functions of Operating Keys" (p.222)

2

Press the 

/

 keys to select “SYSTEM” and press the 

 key. 

3

Press the 

/

 keys to select “H.CALIB”, then press the 

 key. 

4

“OK/CAN” is displayed on the sub-display. 

Press the 

 key to execute calibration or the 

 key to cancel. 

5

Press and hold the 

 key for two seconds or more to enter the RUN 

mode.
To save the setting, refer to "7-3 Functions of Operating Keys" (p.222).

Important

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды