Omron ZW-7000 Series Скачать руководство пользователя страница 253

Страница: 253 / 336

Setting the Output Conditions

ZW-8000/7000/5000
User's Manual

251

Senso

r con

trol
ler
ope

ons

Setting Hold

Setting the Hold Mode

Setting the Hold Mode p.160

As an example, here is an explanation of the procedure for selecting the “PEAK” hold mode setting.

Operating procedure

Steps

Key operation

Display

Description

Press and hold the

key for two seconds or more to enter the

FUNC mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Press the

key to select MEAS, then press the

key.

Press the

key to select TASK1, then press the

key.

Press the

keys to select “OUTPUT” and press the

key.

Press the

keys to select “HOLD” and press the

key.

Press the

keys to select “TYPE” and press the

key.

Set the hold mode.

PEAK: Peak
BOTTOM: Bottom
P-P: PEAK TO PEAK
AUTOPK: AUTO PEAK
AUTOBT: AUTO BOTTOM
AUTOPP: AUTO PEAK TO PEAK
AVE: AVERAGE
SAMPLE: Sampling
OFF: Through

The current setting value is displayed on the sub-display.

Press

key to enter editing mode and the sub-display blinks.

In this example, select “PEAK” and press the

key.

Press and hold the

key for two seconds or more to enter the

RUN mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды