Omron ZW-7000 Series Скачать руководство пользователя страница 239

Страница: 239 / 336

Setting Measurement Items

ZW-8000/7000/5000
User's Manual

237

Senso

r con

trol
ler
ope

ons

7-7 Setting Measurement Items

Measuring the Height

Measuring the Height p.138

As an example, here is an explanation of the procedure for measuring the height of the surface (2nd surface)

below a transparent object (as shown in the diagram on p.138).

Operating procedure

Steps

Key operation

Display

Description

Press and hold the

key for two seconds or more to enter the

FUNC mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Press the

key to select MEAS, then press the

key.

Press the

key to select TASK1, then press the

key.

Press the

keys to select “ITEM” and press the

key.

Press the

keys to select “HEIGHT” and press the

key.

Select the measurement surface.

EDGE1 to EDGE4: 1st surface to 4th surface
PEAK: Peak

“SUR” is displayed on the main display and the current setting value
is displayed on the sub-display.

Press

key to enter editing mode and the sub-display blinks.

In this example, select “EDGE2” and press the

key.

Press and hold the

key for two seconds or more to enter the

RUN mode.
To save the setting, refer to "7-3 Functions of Operating Keys"
(p.222).

Содержание ZW-7000 Series

















































































































































































































































































































































Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды

Omron ZW-7000 Series, Руководство пользователя

Результаты поиска

Содержание ZW-7000 Series

Отзывы:

Бренды по названию

Популярные бренды