manualshive.com logo in svg

Omron ZW-7000 Series, Руководство пользователя

Поделиться
Скачать
Omron ZW-7000 Series Скачать руководство пользователя страница 174

Setting the Output Conditions

172

ZW-8000/7000/5000 

User's Manual

Setting the Zero Reset Memory

Select whether or not to hold the measured value zero reset level even if the power is turned OFF.

As shown in the figure below, use the zero reset memory still set to “OFF” when using this function to perform a 

zero reset at each measurement.

Example: When the level difference of a measurement target is measured

• When zero reset memory is set to “ON”, the zero reset is written to EEPROM (non-volatile memory) in the Sensor 

Controller each time that a zero reset is performed. The EEPROM can be written a maximum of 1,000,000 times. 

Pay attention to the maximum number of writing allowed when this is set to “ON.”

• Even if zero reset memory is disabled, the zero reset level will be held also when the setting is saved. In this 

instance, the zero reset will also be continued after a restart.

Item

Setting item

Setting value

Description

Sensor settings

Zero reset memory

OFF (default 
value)

The zero reset is canceled when the power is turned OFF.

ON

The zero reset level is held even if the power is turned OFF.

This step is 
measured.

Sensor head

Zero reset
executed.

Direction of movement

Zero reset
executed.

Zero reset
executed.

Important

Содержание ZW-7000 Series

















































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды